【单选题】
可编程序控制器自检结果首先反映在各单元面板上的___上。
A. 七段码指示灯
B. LED 指示灯
C. 信号灯
D. 指针
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
___不是运行指示灯不亮的原因。
A. 输入回路有故障
B. 单元内部有故障
C. 远程I/O站的电源未通
D. 程序错误
【单选题】
___不是输人全部不接通而且输人指示灯均不亮的原因。
A. 公共端子螺钉松动
B. 单元内部有故障
C. 远程I/O站的电源未通
D. 未加外部输入电源
【单选题】
正常时每个输出端口对应的指示灯应随该端口有输出或无输出而亮或熄。否则就是有故障。其原因可能是___。
A. 输出元件短路
B. 开路
C. 烧毁
D. 以上都是
【单选题】
正常时每个输出端口对应的指示灯应随该端口___。
A. 无输出或无输出而亮或熄
B. 有输出或无输出而亮或熄
C. 有无输入而亮或熄
D. 有无输入均亮
【单选题】
总体检查时检查运行指示灯是否亮。如果不亮,则检查___。
A. 电源电路
B. 有何异常情况发生
C. 电源指示灯是否正常
D. 输入输出是否正常
【单选题】
运行指示灯是当可编程序控制器某单元运行、___正常时,该单元上的运行指示灯一直亮。
A. 自检
B. 调节
C. 保护
D. 监控
【单选题】
F系列可编程序控制器定时器用___表示。
A. X
B. Y
C. T
D. C
【单选题】
F系列可编程序控制器中的OR指令用于___。
A. 常闭触点的串联
B. 常闭触点的并联
C. 常开触点的串联
D. 常开触点的并联
【判断题】
测量用电流互感器至电能表的二次导线截面积应按电流互感器额定二次负荷计算确定,至少应不小于6 mm2。
A. 对
B. 错
【判断题】
10kV电流互感器二次绕组K2端要可靠接地。
A. 对
B. 错
【判断题】
10kV高供低计用户电流互感器变比为600/5,则倍率为12000。
A. 对
B. 错
【判断题】
3×5A,3×100V三相三线有功表,经200/5A电流互感器和10000/100V的电压互感器计量,则其实用倍率为4000。
A. 对
B. 错
【判断题】
电压互感器超过2倍额定电压下过电压运行,从而引起一、二次绕组过电流而致烧坏。
A. 对
B. 错
【判断题】
变换交流电流的互感器称为电压互感器。
A. 对
B. 错
【判断题】
测量用电压互感器至电能表的二次导线二次导线截面积应按允许的电压降计算确定,至少应不小于2.5 mm2。
A. 对
B. 错
【判断题】
单相电压、电流互感器有加、减极性。
A. 对
B. 错
【判断题】
当电压互感器二次负荷的导纳值减小时,其误差的变化是比值差的变化是比值差往负,相差往正。
A. 对
B. 错
【判断题】
当电压互感器一、二次绕组匝数增大时,其误差的变化是减小。
A. 对
B. 错
【判断题】
电流互感器产生误差的主要原因是产生互感器铁芯中磁通的激磁电流。
A. 对
B. 错
【判断题】
电流互感器的二次负荷随着二次电流的增加而增加。
A. 对
B. 错
【判断题】
电流互感器的负荷与其所接一次线路上的负荷大小有关。
A. 对
B. 错
【判断题】
电流互感器二次绕组可以开路,不可以短路。
A. 对
B. 错
【判断题】
电流互感器将L1和K1连接,通过K1接到电能表接线盒电流、电压共用端钮上时,互感器二次侧不能再接地。
A. 对
B. 错
【判断题】
电流互感器为减极性时一次L1为流入端,那么二次K1也为流入端。
A. 对
B. 错
【判断题】
电流互感器一次L1为流入端,那么二次K1也为流入端。
A. 对
B. 错
【判断题】
电流互感器一次侧反接,为确保极性正确,二次侧不能反接。
A. 对
B. 错
【判断题】
电流互感器在运行中二次回路不允许开路,否则易引起高电压,危及人身与设备安全。
A. 对
B. 错
【判断题】
电流互感器在运行中严禁二次短路。
A. 对
B. 错
【判断题】
电压互感器的额定二次负荷是指电压互感器二次所接电气仪表和二次接线等电路总导纳。
A. 对
B. 错
【判断题】
电压互感器的空载误差与铁芯的导磁率成正比。
A. 对
B. 错
【判断题】
电压互感器的误差分为比差和角差。
A. 对
B. 错
【判断题】
电压互感器的正常运行状态实质上为变压器的短路运行状态。
A. 对
B. 错
【判断题】
电压互感器与变压器相比,二者在工作原理上没有什么区别,电压互感器相当于普通变压器处于空载运行状态。
A. 对
B. 错
【判断题】
对一般的电流互感器来说,当二次负荷的cosφ值增大时,其误差偏负变化。
A. 对
B. 错
【判断题】
二次侧5A的单相电流互感器额定容量为25VA,则额定阻抗为1欧姆。
A. 对
B. 错
【判断题】
互感器二次电压或电流相位反向后的相量超前于一次电压或电流相量时,则相位差为负值,反则为正值。
A. 对
B. 错
【判断题】
三相三线电能计量装臵中,若“+”角差对A相电流互感器的综合误差产生“+”方向的变化,则“+”角差对C相电流互感器的综合误差产生“-”方向的变化。
A. 对
B. 错
【判断题】
在现场检验的全过程中,严禁交流电压回路开路。
A. 对
B. 错
【判断题】
ABC三相电流互感器在运行中其中一相因故变比换大,总电量计量将增大。
A. 对
B. 错
【判断题】
C相电压互感器二次侧断线,将造成三相三线有功电能表可能正转、反转或不转。
A. 对
B. 错
推荐试题
【判断题】
在抗日战争的初期和中期,游击战争虽然不具有战略地位,但起到了阻止日军进攻、减轻正面战场压力的作用。
A. 对
B. 错
【判断题】
在抗日民族统一战线中,中国共产党必须坚持独立自主原则,既统一,又独立。
A. 对
B. 错
【判断题】
对抗日统一战线中的中间势力,中国共产党必须贯彻又联合又斗争的政策。
A. 对
B. 错
【判断题】
在中国共产党七大上,毛泽东明确提出了“马克思主义中国化”这个命题。
A. 对
B. 错
【判断题】
新民主主义理论的系统阐明,标志着毛泽东思想得到多方面展开而达到成熟。
A. 对
B. 错
【判断题】
反对宗派主义以整顿党风,是延安整风运动最主要的任务。
A. 对
B. 错
【判断题】
1945年8月14日,日本天皇广播“终战诏书”,标志着中国人民抗日战争战争胜利结束。
A. 对
B. 错
【判断题】
中国的抗日战争开辟了世界第一个大规模反法西斯战场,是世界反法西斯战争的东方主战场。
A. 对
B. 错
【判断题】
美国是最早为中国抗日战争提供援助的国家。
A. 对
B. 错
【判断题】
中国人民抗日战争,是近代以来中华民族反抗外敌入侵第一次取得完全胜利的民族解放战争。
A. 对
B. 错
【判断题】
世界反法西斯力量对中国的支持,是中国人民抗日战争胜利的决定性因素。
A. 对
B. 错
【判断题】
二战以后,在国共问题上,美国奉行中立政策,要求国民党和共产党和平解决政治纷争,反对国民党政府打内战。
A. 对
B. 错
【判断题】
抗战胜利后,国民党统治集团的根本目标是使中国恢复到战前的状态,继续走资本主义发展道路。
A. 对
B. 错
【判断题】
抗战胜利初期,中国民主同盟主张“以民主的方式争取民主,以合法地行动争取合法的地位”,企图走第三条道路。
A. 对
B. 错
【判断题】
1946年1月政治协商会议决议虽不是新民主主义性质的,但在一个时期内,是否忠实履行它,是人民衡量政治是非的重要尺度。
A. 对
B. 错
【判断题】
从1946年到1949年,中国共产党领导中国人民解放军,经过战略防御、战略相持、战略反攻三个阶段,最后打败了国民党,取得了解放战争的胜利。
A. 对
B. 错
【判断题】
《中国土地法大纲》是中国共产党制定和颁布的第一个土地改革法令,为打败蒋介石、建立新中国的建立奠定了深厚的群众基础。
A. 对
B. 错
【判断题】
国统区第二条战线的形成,表明在不仅在军事战线上,而且在政治战线上,国民党都打了败仗。
A. 对
B. 错
【判断题】
抗战胜利后,一些民主党派领导人所主张的“中间路线”实质上就是资产阶级共和国方案,是旧民主主义的道路。
A. 对
B. 错
【判断题】
内战爆发后,客观形势决定了人民没有走中间路线的余地,原先主张走第三条道路的各党派都靠近了中国共产党,站到了新民主主义革命的立场上来。
A. 对
B. 错
【判断题】
1949年9月的召开的中国人民政治协商会议,是新中国的创建会议,《共同纲领》起着临时宪法的作用。
A. 对
B. 错
【判断题】
民主党派参加新政协并在新中国参政,标志着民主党派地位的根本变化,它们不再是在野党,成为了中国人民民主专政的参加者。
A. 对
B. 错
【判断题】
人民民主专政的新中国的创建,标志着近代以来中国面临的两大历史任务的基本完成。
A. 对
B. 错
【单选题】
A vSphere content library administrator is attempting to unpublish the content library, but the option is grayed out as shown in the Exhibit. Which statement identifies the reason for not being able to unpublish? ___
A. The content library is optimized for syncing over HTTP.
B. A synchronization operation is in progress with this content library.
C. There are active subscriptions on this content library.
D. Underlying storage for this content library is not accessible.
【单选题】
Assuming a mirrored (RAID-1) object configuration, how many hosts must contribute storage in a non-stretched VMware vSAN cluster to satisfy the “Number of failures to tolerate” policy option?“n” is the desired “Number of failures to tolerate” value for all options.___
A. 2n+2
B. 2n
C. 2n+1
D. 3n
【单选题】
An administrator must change the statistics level for short-term performance monitoring and wants to collect metrics for all counters, excluding minimum and maximum rollup values. What would be the statistics level?___
A. Level 3
B. Level 1
C. Level 2
D. Level 4
【单选题】
In a vSphere environment, two resource pools are created as shown in the Exhibit. Each VM is configured with 1 GB of memory. When the administrator tried to power on VM3, the operation failed. What action in the resource pool settings will allow VM3 to power on successfully?___
A. Deselect Expandable Memory Reservation
B. Increase Memory Reservation
C. Deselect Expandable CPU Reservation
D. Increase the CPU Reservation
【单选题】
Which network is used by vSphere HA when VMware vSAN is enabled?___
A. Management network
B. vSphere Replication network
C. vMotion network
D. VSAN network
【单选题】
Which statement is correct when migrating from a Windows vCenter Server to the vCenter Server Appliance 6.5?___
A. Migration deployments do not migrate local OS users from the source vCenter Server.
B. Migration deployments support DHCP on the source vCenter Server.
C. Migration deployments allow the source vCenter Server to remain powered on afterwards.
D. Migration deployments support custom ports for all services on the source vCenter Server.
【单选题】
How can failback of a recovered virtual machine in vSphere Replication be performed?___
A. No action required, because failback is automatically performed to the source site.
B. Configure a new replication in the reverse direction at the target site.
C. Disable or Stop the virtual machine replication on the source site.
D. Power off and unregister the virtual machine on the target site.
【单选题】
After upgrading the vSphere infrastructure and VMware Tools to version 6.5, the “Upgrade VM Compatibility” option is grayed out in the vSphere Web Client. (See Exhibit.) What must the administrator do to enable the VM compatibility upgrade?___
A. VMware Tools should be upgraded last.
B. Restart the ESXi server.
C. Uninstall VMware Tools.
D. Power off the virtual machine.
【单选题】
What availability mode does vCenter HA provide?___
A. Active-Passive
B. Active-Standby
C. Active-Active
D. Load-balanced
【单选题】
In which scenario will vSphere DRS balance resources when set to Fully Automated?___
A. Hosts with only shared storage
B. Hosts are part of a vSphere HA cluster
C. Power Management is set to Balanced on hosts
D. Hosts with shared or non-shared storage
【单选题】
What VMware technology can be used to move physical servers to the vSphere infrastructure?___
A. VMware vMotion
B. VMware Converter
C. VMware vCenter Server
D. OVF transport
【单选题】
Upgrading vCenter Server with Microsoft SQL database fails with the following error message: The DB User entered does not have the required permissions needed to install and configure vCenter Server with the selected DB. Please correct the following error(s): %sWhat could cause this error?___
A. incorrect ports open on SQL Server
B. incorrect database on the SQL server
C. incorrect compatibility mode on the SQL server
D. incorrect permission on SQL Server database
【单选题】
What is a potential downside of having more than four paths per datastore?___
A. limits the storage protocols
B. increases storage latency for VM
C. limits the path selection policies
D. limits the number of LUNs per host
【单选题】
Which feature facilitates the sharing of templates via vCenter Server?___
A. Content Library
B. OVF
C. folders
D. vApp
【单选题】
A vSphere Administrator is in the process of configuring replication for a virtual machine, but is not able to select the Recovery Point Objective (RPO) value of 5 minutes. Which statement could explain why the RPO value cannot be lower than 15 minutes?___
A. The OS quiescing option is selected for Replication options.
B. The virtual machine hardware version is not compatible.
C. The target and source sites use different types of datastores.
D. The target and source sites are not using VMFS 6.0 datastore.
【单选题】
What advanced parameter defines a custom isolation IP address for a vSphere HA cluster?___
A. das.usedefaultisolationaddress
B. das.isolationshutdowntimeout
C. fdm.isolationpolicydelaysec
D. das.isolationaddress
【单选题】
Which method is supported for backing up the virtual machine that contains vCenter Server?___
A. differential
B. incremental
C. full image
D. individual disks