【单选题】
焊接裂纹在重要的焊接接头中是____存在的一种缺陷___
A. 允许
B. 数量不多时允许
C. 不允许
D. 数量多时允许
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
C
解析
暂无解析
相关试题
【单选题】
电弧焊是利用____作为热源的熔焊方法___
A. 电弧
B. 气体燃烧火焰
C. 化学反应热
D. 电能
【单选题】
下列焊接方法中属于固态焊接的是___
A. 熔化极气体保护焊
B. 埋弧焊
C. 摩擦焊
D. 手工电弧焊
【单选题】
目前CO2气体保护焊主要用于___
A. 低碳钢和低合金钢
B. 低合金钢和高合金钢
C. 不锈钢和高合金钢
D. 不锈钢和耐热钢
【单选题】
磁弧焊接的特性下列哪种不适合___
A. 熔化焊
B. 固态焊
C. 压力焊
D. 需焊接保护气体
【单选题】
温锻生产过程中,加热机出料槽剔出的坯料,采用_____方式冷却___
A. 风冷
B. 水冷
C. 自然冷却
D. 冰块
【单选题】
温锻生产过程中,坯料使用____方式加热到生产温度___
A. 电加热
B. 煤炭
C. 煤气
D. 天然气
【单选题】
SDS抛丸机抛丸坯料用的抛丸砂一般是_____材质___
A. 钢铁
B. 铜
C. 陶瓷
D. 塑料
【单选题】
精锻棒料落料后,下道工序是___
A. 抛丸
B. 上料
C. 加热
D. 温锻
【单选题】
坯料加热过程中,采用_____对加热温度进行监测,确保符合工艺温度要求___
A. 手持式测温仪
B. 高温测温仪
C. 在线测温仪
D. 目测
【单选题】
精锻预热坯料温度是___
A. 100~160℃
B. 200~260℃
C. 300~360℃
D. 400~460℃
【单选题】
精锻锻打前坯料温度是___
A. 850~940℃
B. 950~1040℃
C. 750~840℃
D. 650~760℃
【单选题】
温锻预涂石墨浓度是___
A. 7~9%
B. 4~9%
C. 1~2%
D. 2~9%
【单选题】
温锻润滑剂是___
A. 石墨
B. 水
C. 油
D. 气
【单选题】
SDS温锻压机有_____工位___
A. 5
B. 2
C. 3
D. 4
【单选题】
申江厂温锻压机是___
A. 2000吨
B. 2500吨
C. 3000吨
D. 4000吨
【单选题】
申江厂冷精整压机是___
A. 400吨
B. 500吨
C. 300吨
D. 800吨
【单选题】
精锻完成锻打后,要经过___
A. 可控冷却
B. 油冷
C. 回火
D. 退火
【单选题】
生产过程中,经可控冷却直接进行下道抛丸和冷精整时,要求在抛丸前用手持测温仪测量毛坯表面温度,要求温度<____℃___
A. 120
B. 150
C. 180
D. 200
【单选题】
冷精整生产线若使用已超过设计寿命的模具时,目测频率必须至少提高___
A. 1/4
B. 1/3
【单选题】
使用皂化工艺生产外星轮冷精整精锻件时,每次外星轮冷精整换模时必须在冲头与芯棒间添加____#抗磨液压油___
A. 44
B. 45
C. 46
D. 47
【单选题】
皂化使用皂化机进行,皂化的工艺参数按工艺卡上要求的设备参数执行,皂化温度是___
A. 50~60℃
B. 40~50℃
C. 30~40℃
D. 20~30℃
【单选题】
冷精整首件送三座标精测的工件尺寸公差需收紧____%___
A. 10
B. 15
C. 20
D. 30
【单选题】
温锻件经抛丸后要求工件表面基本呈 ___
A. 灰色
B. 黑色
C. ,金属色
D. 氧化色
【单选题】
皂化冷精整后的工件需要进行____处理___
A. 清洗
B. 抛丸
C. 防锈
D. 沥干
【单选题】
外星轮经可控冷却输送带后,柄部硬度一般为___
A. HB109~120
B. HB200~300
C. HB209~252
D. HB300~400
【单选题】
外星轮经可控冷却输送带后,锻件柄部晶粒度要求为___
A. 5~6级
B. 5~7级
C. , 5~9级
D. 5~10级
【单选题】
操作面板上的“OFFSET”是什么含义___
A. 编辑
B. 刀具偏置补偿
C. 自动加工
D. 手动模式
【单选题】
SDS-TQ GF6壳体软加工的主要工艺道序为___
A. 铣削-磨削-清洗
B. 刨削-刮削-车削
C. 车削-铣削-平衡
D. 清洗-磨削-铣削
【单选题】
SDS-TQ产品机加工的一般工艺流程为___
A. 软加工-热处理-硬加工
B. 软加工-硬加工
C. 硬加工-热处理
D. 热处理-软加工
【单选题】
车刀刀片牌号"CNMG120412"中的"N"含义是___
A. 刀具有效切削刃长度
B. 刀具切削槽的形式
C. 刀具切削后角的度数
D. 刀具切削前角的度数
【单选题】
标准麻花钻的锋角为___
A. 118°
B. 35° ~ 40°
C. 50° ~ 55°
D. 55° ~ 60°
【单选题】
闭环控制系统的位置检测装置一般安装在___
A. 传动丝杠上
B. 伺服电机轴上
C. 机床位移部件上
D. 加工工件上
【单选题】
通常CNC系统将零件加工程序输入后,存放在___
A. RAM中
B. ROM中
C. EPROM中
D. 硬盘中
【单选题】
选择加工表面的设计基准为定位基准的原则称为___
A. 基准重合
B. 基准统一
C. 互为基准
D. 无所谓
【单选题】
能改善材料加工性能的措施是___
A. 增大刀具前角
B. 适当的热处理
C. 加大切削用量
D. 减小切削用量
【单选题】
工件上用于定位的表面是确定工件位置的依据,称为___
A. 设计基准
B. 工艺基准
C. 定位基准
D. 加工基准
【单选题】
GF6差速器总成清洁度要求为___
A. ≤0.6mg
B. ≤2mg
C. ≤6mg
D. ≤8mg
【单选题】
GF6差速器BACKLASH的检验要求是___
A. ≤2.36mm
B. ≤3.36mm
C. ≤4.36mm
D. ≤6.36mm
【单选题】
GF6差速器回转检查的要求是___
A. 转动顺畅无卡滞
B. 允许有轻微卡滞
C. 需要很大力气才能转动
D. 有间隙
【单选题】
GF6差速器安装PIN的个数是___
A. 3个
B. 2个
C. 1个
D. 0个
推荐试题
【单选题】
Cancer is second only __________ heart disease as a cause of death.___
A. of               
B. to        
C. with           
D. from
【单选题】
The manager needs an assistant that he can _________ to take care of problems in his absence.___
A. count on      
B. count in      
C. count up      
D. count out
【单选题】
We gave out a cheer when the red roof of the cottage came __________ view.___
A. from             
B. in         
C. before          
D. into
【单选题】
They took ________ measures to prevent poisonous gases from escaping.___
A. fruitful         
B. beneficial   
C. valid             
D. effective
【单选题】
Doing your homework is a sure way to improve your test scores, and this is especially true _______ it comes to classroom tests.___
A. when             
B. since       
C. before           
D. after
【单选题】
In developing countries people are _______ into overcrowded cities in great numbers.___
A. breaking       
B. filling     
C. pouring         
D. hurrying
【单选题】
There are other problems which I don't propose to ____________ at the moment.___
A. go into        
B. go around     
C. go for         
D. go up
【单选题】
It is quite necessary for a qualified teacher to have good manners and _________ knowledge.___
A. extensive      
B. expansive     
C. intensive       
D. expensive
【单选题】
I'm not sure whether I can gain any profit from the investment, so I can't make a(n) ______ promise to help you.___
A. exact             
B. defined     
C. definite         
D. sure
【单选题】
The sports meet, originally due to be held last Friday, was finally ________ because of the bad weather.___
A. set off             
B. broken off      
C. worn off         
D. called off
【单选题】
It has been revealed that some government leaders _______ their authority and position to get illegal profits for themselves.___
A. employ       
B. take     
C. abuse         
D. overlook
【单选题】
Shelly had prepared carefully for her biology examination so that she could be sure of passing it on her first ________.___
A. intention     
B. attempt  
C. purpose     
D. desire
【单选题】
The store had to _______ a number of clerks because sales were down.___
A. lay out          
B. lay off      
C. lay aside       
D. lay down
【单选题】
All the students in this class passed the English exam ________ the exception of Li Ming.___
A. on                   
B. in      
C. for                 
D. with
【单选题】
Writing is a slow process, requiring _______ thought, time, and effort.___
A. significant     
B. considerable    
C. enormous     
D. numerous
【单选题】
Lightning is a ______ of electrical current from a cloud to the ground or from one cloud to another.___
A. rush                 
B. rainbow   
C. rack                 
D. ribbon
【单选题】
I caught a ________ of the taxi before it disappeared around the corner of the street.___
A. vision             
B. glimpse   
C. look               
D. scene
【单选题】
Students or teachers can participate in excursions to lovely beaches around the island at regular _________.___
A. gaps               
B. rate       
C. length             
D. intervals
【单选题】
Physics is ________ to the science which was called natural philosophy in history.___
A. alike               
B. equivalent  
C. likely               
D. uniform
【单选题】
The new appointment of our president _______ from the very beginning of next semester.___
A. takes effect   
B. takes part  
C. takes place     
D. takes turns
【简答题】
绩效
【简答题】
素质测评
【简答题】
素质测评和绩效考评的区别
【简答题】
选拔性测评
【简答题】
配置型测评
【简答题】
开发性测评
【简答题】
诊断性测评
【简答题】
考核性测评
【简答题】
按测评的目的与用途划分有
【简答题】
选拔性测评的特点
【简答题】
考核性测评的特点
【简答题】
量化
【简答题】
类别量化
【简答题】
模糊量化
【简答题】
顺序量化
【简答题】
等距量化
【简答题】
比例量化
【简答题】
当量量化
【简答题】
量化的作用
【简答题】
权重