【判断题】
经纬仪整平时,经反复调整,直到仪器转到任意位置时,水准气泡最大偏离值小于二分之一格为止
A. 对
B. 错
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【判断题】
刮削大型机床导轨面时,应在将导轨面上的零件全部拆除后进行,以保证刮削质量
A. 对
B. 错
【判断题】
要安排好培训计划,做好上课的准备工作,做到有组织,有计划地进行培训,做到定时间,定地点,定内容,定进度,定要求,有练习,有考核
A. 对
B. 错
【判断题】
轨道制作主要是轨道调直和接头,调直后对轨道进行编号,两条轨道上从端部或伸缩缝处算起,轨道接头至少要对齐,以使运转平稳
A. 对
B. 错
【判断题】
为实现电动机连续正转运行需采用具有接触器自锁的控制线路和手动正转控制回路
A. 对
B. 错
【判断题】
在修理带传动机构时,发现带轮孔超差额0.08mm,造成配合过松,一般可用镀铬法来加大轴颈尺寸
A. 对
B. 错
【判断题】
用经纬仪和平行光管测量机床转台分度误差时,应用专用心轴配装在转台中心孔中将经纬仪和心轴紧固联接在一起
A. 对
B. 错
【判断题】
采用双螺母螺纹式调整滚珠丝杠轴向间隙的方法结构紧凑,调整方便,应用广泛
A. 对
B. 错
【判断题】
若自准直仪上读数鼓轮每格角值分度值为1",则其线值分度值可用0.05mm/m表示
A. 对
B. 错
【判断题】
所有的紫色酒精,在 1 米内不准点有明火,不准放在暖气片上
A. 对
B. 错
【判断题】
固定式装配适用于单件和小批量模具的装配,以及装配精度要求较高,需要调整的部位较多的装配
A. 对
B. 错
【判断题】
我国对企业发生的事故,坚持“四不放过”原则进行处理
A. 对
B. 错
【判断题】
齿轮的齿侧间隙分为12 个等级
A. 对
B. 错
【判断题】
在机械设备中,凸轮表面误差将会引起扭转振动
A. 对
B. 错
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
A. 24
B. 48
C. 64
D. 128
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
推荐试题
【单选题】
电源防雷箱的的功率应不大于被保护设备总用电量的_______。[331010103]___
A. 1.2倍
B. 2倍
C. 2.2倍
D. 2.5倍
【单选题】
室内数据传输线长度在_______时,可在一端设备接口处设置防雷保安器。[332030203]___
A. 30m~50m
B. 50m~80m
C. 50m~100m
D. 60m~120m
【单选题】
室内数据传输线长度大于_______时,宜在两端设备接口处设置防雷保安器。[322030203]___
A. 50m
B. 80m
C. 100m
D. 120m
【单选题】
采集驱动信号传输线选用冲击通流量1.5kA,限制电压不大于_______的防雷保安器。[331010102]___
A. 60V
B. 80V
C. 110V
D. 220V
【单选题】
视频信号传输线选用冲击通流量1.5kA,限制电压不大于_______的防雷保安器。[331010101]___
A. 10V
B. 30V
C. 50V
D. 60V
【单选题】
交流轨道电路选用防雷保安器:工作电压小于36V时,限制电压应小于或等于_______。[331010101]___
A. 60V
B. 110V
C. 190V
D. 220V
【单选题】
交流轨道电路选用防雷保安器:工作电压36V~60V时,限制电压应小于或等于_______。[331010101]___
A. 220V
B. 330V
C. 350V
D. 380V
【单选题】
交流轨道电路选用防雷保安器:工作电压60V~110V时,限制电压应小于或等于_______。[331010101]___
A. 380V
B. 500V
C. 700V
D. 1000V
【单选题】
交流轨道电路选用防雷保安器:工作电压110V~220V时,限制电压应小于或等于_______。[331010101]___
A. 380V
B. 500V
C. 700V
D. 1000V
【单选题】
直流轨道电路选用防雷保安器:工作电压小于24V时,限制电压应小于或等于_______。[331010102]___
A. 60V
B. 75V
C. 110V
D. 220V
【单选题】
贯通地线在信号机房建筑物一侧每隔2m~3m用裸铜线与环形接地装置连接,两端各连接_______。[311030203]___
A. 一次
B. 两次
C. 三次
D. 四次
【单选题】
无线天线避雷针的接地装置应单独设置,并距环形接地装置_______以上。[311010103]___
A. 15m
B. 20m
C. 25m
D. 30m
【单选题】
无线天线避雷针的接地装置应单独设置,特殊情况下距环形接地装置不应小于_______。[311010103]___
A. 5m
B. 8m
C. 10m
D. 15m
【单选题】
ZPW-2000A无绝缘移频自动闭塞系统补偿电容采用_______进行现场设置。[312030201]___
A. △法
B. 每100m装一个
C. 等差法
D. 等间距法
【单选题】
ZC-8接地电阻测量仪在使用时,两接地棒即电位探针P'和电流探针C'沿直线相距_______。[322010103]___
A. 15m
B. 20m
C. 25m
D. 30m
【单选题】
S700K型电动转辙机因故不能转换到底时,电流一般不大于_______。[313010102]___
A. 1A
B. 3A
C. 5A
D. 8A
【单选题】
S700K电动转辙机的单线圈电阻不大于_______。[323010103]___
A. 50Ω
B. 54Ω
C. 58Ω
D. 64Ω
【单选题】
S700K电动转辙机代号A15/A16的输出额定转换力为_______。[311010103]___
A. 2500N
B. 3000N
C. 4500N
D. 6000N
【单选题】
S700K电动转辙机代号A17/A18的输出额定转换力为_______。[311010103]___
A. 2500N
B. 3000N
C. 4500N
D. 6000N
【单选题】
S700K电动转辙机代号A33/A34的输出额定转换力为_______。[311010103]___
A. 2500N
B. 3000N
C. 4500N
D. 6000N
【单选题】
JM-A型密贴检查器表示杆动程为_______。[311010103]___
A. 30mm~97mm
B. 65mm~120mm
C. 65mm~140mm
D. 90mm~150mm
【单选题】
JM-A型密贴检查器挤岔断表示的动程:从启动片的滚轮接触表示杆斜面开始为_______。[311010103]___
A. 10mm~13mm
B. 15mm~18mm
C. 15mm~20mm
D. 19mm~25mm
【单选题】
下列关于JM-A型密贴检查器说法正确的是:_______。[331010103]___
A. 每台密贴检查器应设有一组表示接点和一组斥离接点
B. 每台密贴检查器应设有一组表示接点和两组斥离接点
C. 每台密贴检查器应设有两组表示接点和一组斥离接点
D. 每台密贴检查器应设有两组表示接点和两组斥离接点
【单选题】
设在道岔两侧的JM-A型密贴检查器,一台密贴检查器的表示杆及其接点组检查尖轨的密贴位置,另一台密贴检查器的表示杆及其接点组检查尖轨的斥离_______以上位置。[331010204]___
A. 60mm
B. 65mm
C. 75mm
D. 78mm
【单选题】
JM-A型密贴检查器动接点环打入静接点片的深度应不小于_______。[332010204]___
A. 3mm
B. 4mm
C. 5mm
D. 6mm
【单选题】
JM-A型密贴检查器滚轮在表示杆缺口中平面或上平面滚动时,启动片离开表示杆的平面应为_______。[331010204]___
A. 0.3mm~0.8mm
B. 0.5mm~1.7mm
C. 0.3mm~2mm
D. 1mm~3mm
【单选题】
下列关于JM-B型密贴检查器说法正确的是:_______。[331010204]]___
A. 每台密贴检查器应设有一组表示接点和一组斥离接点
B. 每台密贴检查器应设有一组表示接点和两组斥离接点
C. 每台密贴检查器应设有两组表示接点和一组斥离接点
D. 每台密贴检查器应设有两组表示接点和两组斥离接点
【单选题】
JM-B型密贴检查器挤岔断表示的动程:从开关轴接触表示杆斜面开始小于或等于_______。[331010204]___
A. 3mm
B. 4mm
C. 5mm
D. 6mm
【单选题】
ELP-319型密贴检查器检测杆与接点座配合工作可检测_______尖轨动程。[331010204]___
A. 90mm~130mm
B. 170mm~190mm
C. 30mm~190mm
D. 50mm~100mm
【单选题】
S700K电动转辙机单芯电缆控制距离可达_______。[331010204]___
A. 1.5km
B. 2.0km
C. 2.5km
D. 3.0km
【单选题】
S700K型电动转辙机上下两检测杆无张嘴和左右偏移现象,检测杆头部的叉形连接头销孔的磨损旷量不大于_______。[312010204]___
A. 0.5mm
B. 1mm
C. 1.5mm
D. 2mm
【单选题】
三相电动机电源线中,任意两根线对调会使电动机_______。[32301024]___
A. 转速变慢
B. 转速变快
C. 不转
D. 反转
【单选题】
ZPW-2000A无绝缘移频自动闭塞系统_______用于实现主轨道电路、小轨道电路的调整。[311010103]___
A. 发送检测器
B. 侧线检测盘
C. 衰耗盘
D. 接收器
【单选题】
ZPW-2000R型无绝缘轨道电路在最不利条件下,用0.15Ω标准分路线分路,主轨道无分路死区段。调谐区分路死区段不大于_______。[331010103]___
A. 2m
B. 3m
C. 4m
D. 5m
【单选题】
ZP·WD型18信息移频轨道电路,在机车入口端轨面,用_______标准分路电阻线分路时,应满足动作机车信号的最小短路电流的要求。[311010103]___
A. 0.03Ω
B. 0.04Ω
C. 0.05Ω
D. 0.06Ω
【单选题】
ZP·WD型18信息移频轨道电路,在调整状态下,受电端接收盒限入电压应不小于_______,轨道电路应可靠工作。[322010101]___
A. 240mV
B. 250mV
C. 280mV
D. 290mV
【单选题】
连接两个节点的一段电路称为_______。[222000000]___
A. 回路
B. 开路
C. 断路
D. 支路
【单选题】
S700K型电动转辙机表示电路中电阻R1的阻值是_______。[312010103]___
A. 300Ω
B. 500Ω
C. 800Ω
D. 1000Ω
【单选题】
S700K型电动转辙机表示电路整流堆部分串入电阻R2的阻值是_______。[312010103]___
A. 300Ω
B. 500Ω
C. 800Ω
D. 1000Ω
【单选题】
信号微机监测系统不能监督与_______结合部有关状态。[311010105]___
A. 电务
B. 车务
C. 机务
D. 工务