【单选题】
HXD3电力机车制动控制司机控制器手柄为___级,级间能平滑调节。
A. 10
B. 12
C. 13
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
HXD3电力机车牵引电动机用冷却风机中的惯性分离过滤器在牵引风机的___使用。
A. 排风侧
B. 进风侧
C. 中部
【单选题】
HXD3电力机车空气压缩机的冷却器是吸收车内的空气,向___直接排气。
A. 车内
B. 车顶
C. 车外(地板下)
【单选题】
HXD3电力机车有___个并联的回流装置 EB1~EB6,从轮对回流至钢轨。
A. 2
B. 4
C. 6
【单选题】
HXD3电力机车高压隔离开关采用电空控制方式进行转换的。当一台受电弓发生故障接地时,可通过控制电器柜上的隔离开关 SA___,将其打至对应隔离位。
A. 95
B. 96
C. 98
【单选题】
HXD3电力机车高压电压互感器次边输出通过保护用的自动开关 QA___,分别送到主变流器UM1和主变流器UM2的控制单元,作为主变流器控制的同步信号使用。
A. 1
B. 2
C. 3
【单选题】
HXD3电力机车低压电流互感器TA___是为电度表的计量提供电流输入,为机车微机控制系统提供原边电流信号,用于原边电流显示。
A. 1
B. 2
C. 3
【单选题】
HXD3电力机车高压接地开关QS10上配有1把蓝色钥匙和___把黄色钥匙。
A. 1
B. 2
C. 3
【单选题】
HXD3电力机车将蓝色钥匙插入接地开关 QS10 并向右旋转至___位,保证车顶设备可靠接地。
A. 运行
B. 中间
C. 接地
【单选题】
HXD3电力机车主变压器的___个1450V牵引绕组分别用于两套主变流器的供电。
A. 2
B. 4
C. 6
【单选题】
HXD3电力机车主变压器___个399V辅助绕组分别用于辅助变流器的供电。
A. 1
B. 2
C. 4
【单选题】
HXD3电力机车每组牵引变流器分别有___个接触器。
A. 1
B. 2
C. 3
【单选题】
HXD3电力机车主接地保护电路由跨接在中间回路的___个串联电容和一个接地信号传感器组成。
A. 两
B. 四
C. 六
【单选题】
HXD3电力机车主变流器含有___套独立的接地保护电路,可以分别对3组牵引变流器进行接地监测和保护。
A. 一
B. 二
C. 三
【单选题】
HXD3电力机车牵引绕组过流故障在3分钟内连续发生___次,故障将被锁定,必须切断 CI 控制电源,才能恢复正常。
A. 两
B. 三
C. 四
【单选题】
HXD3电力机车主电路某一点接地时则形成回路,接地检测回路有故障电流流过,传感器输出电流信号,使保护装置动作,其动作保护值为___A。
A. 5
B. 8
C. 10
【单选题】
HXD3电力机车当原边网压高32kV且持续___ms 或者是高于35kV且持续1ms时,CI 实施保护。
A. 3
B. 5
C. 10
【单选题】
HXD3电力机车当原边网压低于16kV且持续___ms时, CI 实施保护。
A. 3
B. 5
C. 10
【单选题】
HXD3电力机车库内电源通过单相插座送到___位牵引电动机的牵引变流器环节,进行库内动车作业。
A. 一、六
B. 二、五
C. 三、四
【单选题】
HXD3电力机车正常情况下,辅助变流器UA11、UA12基本上以___%的额定容量工作。
A. 40
B. 50
C. 60
【单选题】
HXD3电力机车当某一套辅助变流器发生故障时,允许___压缩机可以投入工作。
A. 两台
B. 操纵端
C. 非操纵端
【单选题】
HXD3电力机车辅助变流器的过流和过载保护故障消除后___s内自动复位。
A. 3
B. 5
C. 10
【单选题】
HXD3电力机车辅助变流器输入回路中的过流和过载保护故障在___分钟内连续发生两次,该辅助变流器将被锁死。
A. 2
B. 3
C. 5
【单选题】
HXD3电力机车辅助电动机回路过载保护动作故障在2分钟内连续发生___次,该辅助变流器将被锁死。
A. 2
B. 4
C. 6
【单选题】
HXD3电力机车最多可以实施同型号的___台机车重联。
A. 2
B. 4
C. 6
【单选题】
当HXD3电力机车速度大于等于___km/h,且机车未实施空气制动时,可进行“定速控制”操作。
A. 10
B. 15
C. 20
【单选题】
HXD3电力机车进入“定速控制”状态后,实际速度大于“目标速度___km/h”时, TCMS控制机车进入电气制动工况。
A. 1
B. 2
C. 3
【单选题】
HXD3电力机车进入“定速控制”状态后,司机控制器调速手柄的级位变化超过___级以上时,机车“定速控制”状态自动解除。
A. 1
B. 2
C. 3
【单选题】
HXD3电力机车制动缸压力高于___kPa时,踏面清扫投入。
A. 50
B. 100
C. 150
【单选题】
HXD3电力机车制动缸压力低于___kPa 时,踏面清扫解除。
A. 50
B. 30
C. 20
【单选题】
HXD3电力机车为防止损坏辅助压缩机,辅助压缩机打风时间不得超过___分钟。
A. 3
B. 5
C. 10
【单选题】
HXD3电力机车受电弓(自绝缘子底面)升高到2m的升弓时间≤___s。
A. 4.5
B. 5.4
C. 6
【单选题】
HXD3电力机车受电弓从2m高度(至绝缘子底面)落下的降弓时间≤___s。
A. 2
B. 3
C. 4
【单选题】
HXD3电力机车转向架构架上侧2轴以及5轴附近的侧档与车体之间每侧的自由横动量为 ___mm。
A. 10
B. 20
C. 30
【单选题】
HXD3电力机车在网压___kV时功率为零。
A. 17.2
B. 19.5
C. 20.2
【单选题】
HXD3电力机车(25t 轴重)恒功率速度范围在___ km/h~120km/h 。
A. 55
B. 65
C. 70
【单选题】
HXD3电力机车应能以___km/h速度安全通过半径为125m的曲线。
A. 3
B. 5
C. 7
【单选题】
HXD3电力机车整体的车内的增压空气量是___m3/s 。
A. 2.6
B. 1.6
C. 3.6
【单选题】
HXD3电力机车主变流器UM1内部可以看成由___个独立的“整流—中间电路—逆变”环节构成。
A. 1
B. 3
C. 6
【单选题】
HXD3电力机车的___个牵引逆变器分别向6台牵引电动机供电。
A. 2
B. 3
C. 6
【单选题】
CCBⅡ制动机实施紧急制动时,送入TCMS___撒砂指令信号要求TCMS根据机车运行方向,进行撒砂控制。
A. 801
B. 803
C. 804
推荐试题
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
A. 24
B. 48
C. 64
D. 128
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.