【多选题】
变压器过负荷时应作___处理。
A. 在变压器过负荷时应投入全部冷却器包括所有备用风扇等；
B. 在过负荷时值班人员应立即降低部分负荷；
C. 变压器在过负荷期间，应加强对变压器的监视；
D. 具体过负荷时间过负荷倍数参照部颁规程处理；
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
ACD
解析
暂无解析
相关试题
【多选题】
变压器新安装或大修后，投入运行前应验收项目有___。
A. 变压器本体无缺陷，外表整洁，无严重渗漏油和油漆脱落现象；
B. 变压器绝缘试验应合格，无遗漏试验项目；
C. 各部油位应正常，各阀门的开闭位置应正确，油的性能试验，色谱分析和绝缘强度试验应合格；
D. 变压器外壳应有良好的接地装置，接地电阻应合格；
【多选题】
变压器的铁芯接地是因为___。
A. 绕组端部电场分布是极不均匀的，铁芯接地可以改善其电场分布；
B. 为了避免变压器的内部放电；
C. 高压绕组与铁芯柱的距离较近，绝缘处理较难，接地使其承受较大的电磁力；
D. 不接地可能会使变压器的铁芯及其他附件感应一定的电压；
【多选题】
变压器的铁芯接地是因为___。
A. 绕组端部电场分布是极不均匀的，铁芯接地可以改善其电场分布；
B. 为了避免变压器的内部放电；
C. 高压绕组与铁芯柱的距离较近，绝缘处理较难，接地使其承受较大的电磁力；
D. 不接地可能会使变压器的铁芯及其他附件感应一定的电压；
【多选题】
氧化锌避雷器有何特点？___。
A. 氧化锌电阻片具有优良的非线性特征；
B. 在正常工作电压下，仅有几百毫安的电流通过，运行中能监测其状况；
C. 当过电压侵入时，电阻片电阻迅速减小，流过电阻片电流迅速增大；
D. 比普通阀型避雷器更小的残压；
【多选题】
断路器拒绝分闸的原因有___。
A. 断路器操作控制箱内“远方--就地”选择开关在就地位置；
B. 弹簧机构的断路器弹簧未储能；
C. 断路器控制回路断线；
D. 分闸线圈故障；
【多选题】
下列对电感L描述正确的是___。
A. 由L=φ/i可知，电感L与电流i成反比；
B. 含有铁芯的线圈的电感L比无铁芯时大得多；
C. 电感L的大小与线圈的尺寸.匝数及线圈内有无铁芯有关；
D. 由L=φ/i可知，电流i越大，磁通φ也越大；
【多选题】
断路器拒绝分闸的原因有___。
A. 断路器操作控制箱内“远方--就地”选择开关在就地位置；
B. 弹簧机构的断路器弹簧未储能；
C. 断路器控制回路断线；
D. 操作继电器故障；
【多选题】
运行中断路器发生误跳闸应作___处理。
A. 若因由于人员误碰，误操作或机构受外力振动，保护盘受外力振动引起自动脱扣而"误跳"应不经汇报立即送电；
B. 若保护误动可能整定值不当或流变.压变回路故障引起的，应查明原因后才能送电；
C. 二次回路直流系统发生两点接地（跳闸回路接地）引起应及时排除故障；
D. 对于并网或联络线断路器发生"误跳"时应立即送电；
【多选题】
GIS设备的常见故障处理有___。
A. 当气室内部电气元件发生异常响声时，应根据声音变化判别是屏蔽罩松动，内部有异物，当出现明显放电声时应采取停电处理；
B. 设备防爆膜破裂，说明内部出现严重的绝缘问题，电弧使设备部件损坏，引起内部压力超过标准，必须进行停电处理；
C. 室外GIS设备发生爆炸和严重漏气等事故时，人员接近设备应选择从上风侧接近设备，穿安全防护服并佩戴隔离式防毒面具，手套和护目眼镜；
D. 室内GIS设备发生爆炸或严重漏气，必须通风机全部开启51min以上，待含氧量和SF6气体浓度符合标准，并采取充分措施准备后，才能进入事故设备装置室进行检查；
【多选题】
断路器出现___异常时应停电处理。
A. 油断路器渗油；
B. SF6断路器的气室严重漏气发出操作闭锁信号；
C. 真空断路器真空损坏；
D. 液压机构的断路器液压突然失压到零；
【多选题】
断路器出现___异常时应停电处理。
A. 油断路器渗油；
B. SF6断路器的气室严重漏气发出操作闭锁信号；
C. 真空断路器真空损坏；
D. 液压机构的断路器液压突然失压到零；
【多选题】
隔离开关与断路器的联锁机构的结构特点是___。
A. 断路器断开后，隔离开关才能打开；
B. 隔离开关断开后，断路器才能打开；
C. 断路器闭合后，隔离开关才能闭合；
D. 隔离开关闭合后，断路器才能闭合；
【多选题】
电压互感器的二次回路通电试验时，为防止由二次侧向一次侧反充电，除应将二次回路断开外，还应取下电压互感器___或断开电压互感（ ）。
A. 高压熔断器；
B. 一次刀闸；
C. 引线；
D. 避雷器；
【多选题】
下列对电压互感器描述正确的是___。
A. 10kV电压互感器一次侧熔断器熔丝的额定电流是0.5A；
B. 电压互感器一次侧熔丝熔断后不允许用普通熔丝代替由于不能满足断流容量要求；
C. 若电压互感器二次侧熔丝容量选择不合理，有可能造成一次侧熔丝熔断；
D. 110KV的电压互感器采用石英砂填充的熔断器具有较好的灭弧性能和较大的断
【多选题】
电流互感器应在___方式下运行。
A. 电流互感器不得超额定容量长期运行；
B. 电流互感器二次侧电路应始终闭合；
C. 电流互感器二次侧线圈的一边和铁芯应同时接地；
D. 电流互感器二次侧线圈应能耐受高压；
【多选题】
使用变频器应注意的事项有___。
A. 变频器输入端要尽量装接断路器；
B. 变频器输出端尽量装设接触器；
C. 变频器输出端要尽量装设电涌抑制器；
D. 面板上的CHARGE灯熄灭后方可进行检修；
【多选题】
消弧线圈送电规定___。
A. 消弧线圈投用前不需测量绝缘电阻；
B. 消弧线圈应在所属变压器投运后投入；
C. 消弧线圈投用必须是在系统无单相接地时；
D. 合上消弧线圈隔离开关后必须检查刀闸接触良好；
【多选题】
消除铁磁谐振过电压方法有___。
A. 拉合断路器，改变运行方式，投入母线，改变接线方式；
B. 投入母线上的备用变压器或所用变压器；
C. 将TV二次回路短接；
D. 投.切电容器或电抗器；
【多选题】
倒停母线时切母联断路器应注意___。
A. 对要停电的母线再检查一次，确认设备已全部倒至运行母线上；
B. 切母联断路器前，检查母联断路器电流表应指示为零；
C. 切母联断路器后，检查停电母线的电压表应指示零；
D. 先拉电压互感器，后切母联断路器；
推荐试题
【单选题】
Which storage feature always requires the use of third-party software on ESXi?___
A. Hardware Acceleration for NAS devices
B. VVOL
C. Hardware Acceleration for Block
D. evices
【单选题】
An ESXi host's VMCA-Signed certificate has expired. How can the certificate be renewed?___
A. In the vSphere Web Client, browse to the host in question. Click the Manage tab and select settings. Select System and click Certificate, then click the Renew button.
B. In the vSphere Web Client, browse to the host in question. Click the Manage tab and select settings. Select System and click Certificate, then click the Refresh CA Certificates button.
C. Run the command /sbin/generate-certificates on the affected host.
D. Disconnect the host from vCenter Server and reconnect it.
【单选题】
Which is the correct order for upgrading vSphere components?___
A. vCenter Server, ESXi hosts, VMware Tools, Virtual Machine hardware
B. VMware Tools, Virtual Machine hardware, ESXi hosts, vCenter Server
C. vCenter Server, Virtual Machine hardware, VMware tools, ESXi hosts
D. ESXi hosts, vCenter Server, Virtual Machine hardware, VMware Tools
【单选题】
Which iSCSI initiator type can be used with any network interface card?___
A. Software iSCSI initiator
B. Software FCoE adapter
C. Hardware Independent iSCSI initiator
D. Hardware Dependent iSCSI initiator
【单选题】
An administrator is attempting to power on a virtual machine with 32GB of memory. The operation fails with the following error: <Could not power on VM: No space left on device> <Checking the space on the virtual machine's datastore, there is 30GB free.> Which action would allow the VM to power on?___
A. Set a 2GB memory reservation on the VM.
B. Mount the virtual disk from the affected VM on to another virtual machine and free up space from within the OS.
C. Enable vSphere HD admission control on the cluster in which the VM resides.
D. Set a 2GB memory limit on the VM.
【单选题】
An administrator attempts to manually reclaim space on thin-provisioned VMFS6 volumes but finds that no additional space is being recovered. Which could be causing this?___
A. vSphere 6.5 does not support manual UNMAP.
B. The manual UNMAP operation has been moved to the vSphere web client.
C. The VASA version is use is incompatible.
D. UNMAP is automated for VMFS6.
【单选题】
An administrator has upgraded to vSphere 6.5 and also wants to use Kerberos authentication for NFS. Which can be done to the existing NFSv3 volumes to enable this feature?___
A. Perform a storage rescan on VMFS volumes.
B. Unmount the NFSv3 datastore, and then mount as NFSv4.1 datastore.
C. Nothing. All NFSv3 mounted datastores are upgraded automatically during vSphere upgrades.
D. Perform a scan of new storage devices.
【单选题】
An administrator wants to restore the vCenter Server Appliance 6.5 from backup. Where can this be accomplished?___
A. from the ESXi Host Client
B. from the VMware vSphere Appliance Management Interface
C. from within the VMware vSphere Web Client
D. from the vCenter Server Appliance Installer
【单选题】
The administrator wants to power on VM-K2, which has a 2GHz CPU reservation. VM-M1, VM-M2, and VM-K1 are all powered on. VM-K2 is not powered on. The exhibit shows the parent and child resource reservations. If Resource Pool RP-KID is configured with an expandable reservation, which statement is true?___
A. VM-K2 will be unable to power on because there are insufficient resources.
B. VM-K2 will be able to power on since resource pool RP-KID has 2GHz available.
C. VM-K2 will be unable to power on because only 2GHz are reserved for RP-KID.
D. VM-K2 will receive resource priority and will be able to power on this scenario.
【单选题】
Which is the block size on the VMFS6 datastore?___
A. All small and large file blocks are 8MB.
B. All small and large file blocks are 1MB.
C. Small file blocks are 512KB. large file blocks are 64MB.
D. Small file blocks are 1MB, large file blocks are 512MB.
【单选题】
When installing vCenter Converter Standalone, why must an administrator perform a client-server installation instead of a local installation?___
A. to manage conversion tasks remotely
B. to convert virtual machines as well as physical machines
C. to allow installation of the Converter agent on remote source machines
D. to hot clone physical or virtual machines
【单选题】
Which is required by vCenter Converter Standalone to convert a physical Red Hat Enterprise Linux 7 machine to a virtual machine?___
A. The Linux machine must be powered off.
B. The Linux machine must have the SSH daemon started.
C. The Linux machine must use a static IP address.
D. The Linux machine must have a fully-qualified domain name.
【单选题】
An administrator is troubleshooting network communications between a vCenter Server and an ESXi 6.5 host. Which log shows the related events between these components?___
A. /var/log/fdm.log
B. /var/log/vpxa.log
C. /var/log/hostd.log
D. /var/log/auth.log
【单选题】
An administrator has recently upgraded from vSphere 6.0 to 6.5, and can no longer see the software iSCSI named vmhba33. Which could be the reason for this?___
A. The upgrade has changed the vmhba name.
B. vSphere 6.5 automates iSCSI configurations.
C. vSphere 6.5 no longer supports software iSCSI.
D. The upgrade has deleted the vmhba.
【单选题】
An administrator is trying to vMotion a VM from his datacenter to a recovery site. Which is the maximum allowed RTT (Round-Trip Time) latency between source and destination host?___
A. 100 milliseconds
B. 150 milliseconds
C. 15 milliseconds
D. 10 milliseconds
【单选题】
Which is required for configuring iSCSI Software Adapter network port binding?___
A. VMkernel of the iSCSI traffic must be load balanced using Route based on IP Hash algorithm.
B. VMkernel of the iSCSI traffic must be load balanced using Route based on Source Virtual Port ID algorithm.
C. VMkernel of the iSCSI traffic must be load balanced using Route based on Source MAC Hash algorithm.
D. VMkernel of the iSCSI traffic must be bound to only one active network adapter.
【单选题】
In vSphere Data Protection 6.1, which is the function of a Backup Verification job?___
A. None. Backup Verification job is not a feature of vSphere Data Protection
B. It is a manual task -Power it on -Verify the guest OS -Check started applications
C. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OS is booted by communicating with the Backup Verification agent
D. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OC is booted by detecting the VMware ToolsTM "heartbeats"
【单选题】
An administrator has enabled vSphere Distributed Switch Health Check. The hosts connected to that Distributed Switch all display an alert:< vSphere Distributed Switch MTU supported status > .The administrator has all of the VMkernel ports MTU sizes set to 1600. Which action will remedy this problem?___
A. Configure the Distributed Switch to MTU 9100.
B. Disconnect and reconnect the physical network cable.
C. Configure the physical switch to MTU 1600.
D. Disable the Distributed Switch MTU.
【单选题】
Which Host Profile Subprofile configuration is used to configure firewall settings for ESXi hosts?___
A. Advanced Configuration Settings
B. General System Settings
C. Security
D. Networking
【单选题】
Where would a vSphere administrator find general vCenter Server logs on a vCenter Server Appliance?___
A. /var/log/vmware/vpxd/
B. /var/log/messages
C. /etc/vmware-vpx/
D. /var/log/vmware/vsan-health/
【单选题】
An administrator wishes to enable network port mirroring based on source port. Which feature should be enabled?___
A. vSphere standard switch port
B. ERSPAN
C. NSX Virtual Wire
D. VLAN
【单选题】
Which CLI command shows the physical uplink status for a vmnic?___
A. esxcli network ip connection list
B. esxcli network ip neighbor list
C. esxcli network nic get
D. esxcli network nic list
【单选题】
Which is the maximum number of block devices (LUNs) that are supported by ESXi hosts that are running version 6.5?___
A. 1024
B. 512
C. 2048
D. 256
【单选题】
When performing a vCenter Server 5.5 for Windows with Microsoft SQL Server Express database migration to vCenter Server Appliance 6.5, which will be the target database?___
A. Microsoft SQL Server Express 2012R2
B. Microsoft SQL Server Standard 2012R2
C. PostgreSQL
D. Oracle DB 11g
【单选题】
An administrator has multiple vCenter Server 6.5 systems but cannot enable Storage I/O Control (SIOC) on a datastore shared by ESXi hosts managed by the vCenter Server systems. Which action should the administrator take to resolve the issue?___
A. Unmount the datastore and then enable SIOC on the vCenter Server system.
B. Configure the datastore to be managed by a single vCenter Server system.
C. Configure Storage DRS and then enable SIOC on the vCenter Server system.
D. Enable Raw Device Mapping (RDM) on the
E. SXi hosts.
【单选题】
“OneAppServer” is a VM template stored in a content library named “LibraryOne”, but the vSphere administrator is not able to use this template for deployment. Why is the administrator unable to deploy OneAppServer?___
A. OneAppServer must be updated before it can be deployed.
B. LibraryOne is a subscribed library and OneAppServer is not downloaded yet.
C. LibraryOne is published and optimized for syncing over HTTP.
D. OneAppServer was imported from a local file on the system.
【单选题】
An administrator sets the Failover Capacity for both CPU and Memory at 25%. Based on the Exhibit below, how much of the cluster’s total CPU resources are still available to power on additional virtual machines?___
A. 45%
B. 25%
C. 70%
D. 60%
【单选题】
Which statement applies to the vSphere Replication appliance?___
A. Only one vSphere Replication appliance can be deployed per vCenter Server instance.
B. VMware Tools in the vSphere Replication appliance can be upgraded.
C. A single vSphere Replication appliance can manage a maximum of 4000 replications.
D. vSphere Replication is available only with the vSphere
E. ssentials Plus license.
【单选题】
Which esxcli namespace can a vSphere Administrator use to adjust the queue depth?___
A. esxcli system module parameters
B. esxcli storage core device
C. esxcli system module set
D. esxcli storage core adapter
【单选题】
Which statement regarding datastore clusters meets VMware’s recommended best practices?___
A. Clusters should contain only datastores presented from the same storage array.
B. Clusters should contain only datastores with equal hardware acceleration capability.
C. Clusters should contain only datastores with the same capacity.
D. Clusters should contain only datastores using the same connection method (iSCSI, FC, etc.).
【单选题】
What VM Monitoring setting would ensure that the maximum reset window for a virtual machine is 24 hours?___
A. Medium
B. Low
C. High
D. Normal
【单选题】
What is the default space threshold for vSphere Storage DRS?___
A. 80%
B. 70%
C. 90%
D. 95%
【单选题】
Which is the correct sequence to upgrade a vSphere infrastructure?___
A. vCenter Server>ESXi host> VMware Tools>VM compatibility
B. ESXi host>vCenter Server> VMware Tools>VM compatibility
C. vCenter host> ESXi host> VM compatibility> VMware Tools
D. ESXi host>vCenter Server> VM compatibility>VMware Tools
【单选题】
An administrator has a large boot from SAN cluster and wants to ensure consistent configuration by using host profiles. What special considerations are required for boot from SAN hosts?___
A. Change the “Device is shared clusterwide” setting to “false” in the host profile.
B. Verify that the boot LUN is correctly identified as the boot device in the host profile.
C. The boot from SAN device must report as a local device.
D. Host profiles are incompatible with boot from SAN hosts.
【单选题】
When using VMware Converter to import a Windows server and improve the consistency of the destination virtual machine, which optional step can be performed immediately prior to powering down the source server?___
A. Perform a final synchronization task.
B. Remove the server from the network.
C. Uninstall production applications.
D. Remove the server from the Active Directory domain.
【单选题】
Restoration of the vCenter Server Appliance is accomplished using which interface?___
A. vSphere Web Client
B. vSphere Client
C. vCenter Server Appliance Management Interface
D. vCenter Server Appliance GUI Installer
【单选题】
When attempting to migrate a virtual machine to another host in the same cluster, the error message, “Select a valid compute resource” returns. What could cause this error?___
A. Both hosts run different versions of ESXi.
B. Both hosts are not sharing the same datastore.
C. VMware Tools is not installed.
D. Virtual machine has an ISO attached.
【单选题】
When will vSphere Data Protection delete the expired backup image of a Platform Service Controller?___
A. Immediately after the retention period has expired.
B. After the expired backup image is restored.
C. During the next backup window following expiry.
D. During the next maintenance window following expiry.
【单选题】
Group A has permission to download files in Content Library. Group B does not have permission to download files in Content Library. If a user is a member of both groups, what will be the result?___
A. The user cannot download file from Content Library.
B. The user can download file from Content Library.
C. The user cannot access Content Library.
D. The user can access Content Library.
【单选题】
An administrator is trying to set up Host Partial Failure Response, but the Automated option is grayed out. What can the administrator change to enable the Automated option?___
A. Change the vSphere DRS Automation level to Partially Automated.
B. Change the vSphere DRS Automation level to Fully Automated.
C. Enable vSphere HA Host Monitoring.
D. Change the vSphere DPM Automation level to Automatic.
