【单选题】
___不是埋弧自动焊最主要的工艺参数
A. 焊接电流
B. 电弧电压
C. 焊接速度
D. 焊丝伸出长度
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
D
解析
暂无解析
相关试题
【单选题】
过低的焊接速度会产生___等缺陷
A. 咬边
B. 焊缝下凹
C. 焊漏
D. 烧穿
【单选题】
埋弧自动焊时焊剂堆积高度一般在___范围比较合适
A. 2.5~3.5mm
B. 5.5~6.5mm
C. 12.5~13.5mm
D. 2.5~3.5cm
【单选题】
埋弧自动焊的坡口形式与焊条电弧焊基本相同,但由于埋弧焊的特点,应采用___
A. 较大的坡口角度
B. 较小的坡口角度
C. 较大的钝边
D. 较大的间隙
【单选题】
板材对接要求全焊透,采用I形坡口埋弧自动焊双面焊,要求后焊的正面焊道的熔深(焊道厚度)达到板厚的___
A. 30%~40%
B. 40%~50%
C. 50%~60%
D. 60%~70%
【单选题】
板材对接要求全焊透,采用I形坡口双面埋弧自动焊工艺,在进行后焊的正面焊道焊接时,若熔池背面为 ___色,表示熔深符合要求
A. 看不见颜色
B. 暗红
C. 淡黄
D. 白亮
【单选题】
埋弧自动焊应注意选用容量恰当的___,以满足通常为100%的满负载持续率的工作需求
A. 弧焊电源
B. 电焊钳
C. —次电源线
D. 焊接电缆
【单选题】
与其他电弧焊相比___不是手工钨极氩弧焊的优点
A. 保护效果好,焊缝质量高
B. 易控制熔池尺寸
C. 可焊接的材料范围广
D. 生产率高
【单选题】
___不是手工钨极氩弧焊的工艺参数
A. 喷嘴直径
B. 气体流量
C. 钨极直径
D. 焊机型号
【单选题】
___不是钨极氩弧焊选择钨极直径的主要依据
A. 焊件厚度
B. 焊接电流大小
C. 电源种类与极性
D. 焊工操作技术
【单选题】
钨极氩弧焊电弧电压增大时,会使单道焊缝___
A. 宽度减小,焊缝厚度增加
B. 宽度减小,余高增加
C. 宽度增加,余高也增加
D. 宽度增加,熔深减小
【单选题】
钨极氩弧焊时,氩气流量根据___来选择
A. 工件厚度
B. 焊丝直径
C. 钨极直径
D. 焊接位置
E. 焊接速度
F. 喷嘴直径
【单选题】
钨极氩弧焊的喷嘴直径可根据钨极直径按经验公式选择:喷嘴直径:(内径,mm)等于钨极直径的(mm)___倍
A. 2.5~3.5
B. 4.5~5.5
C. 6.5~7.5
D. 8~9
【单选题】
易燃物品距离钨极氩弧焊场所不得小于___ m
A. 5
B. 13
C. 15
D. 20
【单选题】
CO2气体保护焊有一些不足之处,但___不是CO2焊的缺点
A. 飞溅较大
B. 焊缝含氢量多
C. 焊缝表面成形较差
D. 弧光较强
【单选题】
___是一种CO2焊可能产生的气孔
A. 氧气孔
B. 氮气孔
C. CO2气孔
D. CO气孔
【单选题】
CO2焊时,于CO2气体具有氧化性,可以抑制___的产生
A. A.二氧化碳气孔
B. B.氢气孔
C. C.氮气孔
D. D.NO气孔
【单选题】
CO2焊如果采用含有硅、锰脱氧元素的焊丝,则 ___飞溅已不显著
A. 焊接工艺参数不当引起的
B. 由极点压力引起的
C. 熔滴短路时引起的
D. 由冶金反应引起的
【单选题】
___不是CO2焊时选择电弧电压的根据
A. 焊接电流
B. 电源种类与极性
C. 焊丝直径
D. 熔滴过渡形式
【单选题】
CO2焊时,焊丝伸出长度通常取决于焊丝直径,约以焊丝直径的 ___倍为宜
A. 5
B. 10
C. 15
D. 20
【单选题】
___不是选择CO2焊气体流量的根据
A. 焊接电流
B. 焊件材料种类
C. 电弧电压
D. 焊接速度
【单选题】
CO2焊的电源种类与极性应采用___
A. 工频交流电源
B. 中频交流电源
C. 直流反接
D. 直流正接
【单选题】
薄板对接仰焊位置半自动CO2焊时,焊接方向应采用___
A. 左焊法
B. 右焊法
C. 立向下焊
D. 立向上焊
【单选题】
中厚板对接平焊位置半自动CO2焊应采用___
A. 左焊法
B. 右焊法
C. 立向下焊
D. 立向上焊
【单选题】
Q235钢C02气体保护焊时,焊丝应选用___
A. H08Mn2SiA
B. H08MnMoA
C. H08MnA
D. H08A
【单选题】
CO2气瓶使用CO2气体电热预热器时,其电压应采用___伏
A. 36
B. 42
C. 48
D. 60
【单选题】
点焊焊件之间的接触电阻大小与___无关
A. 焊件直径
B. 电极材料
C. 电极压力
D. 通电时间
【单选题】
电阻焊焊件导电部分的电阻大小与焊件材料的电阻率___
A. 没有关系
B. 成反比
C. 关系不大
D. 有很大关系
【单选题】
对焊机按___分有电阻对焊机和闪光对焊机
A. 工艺方法
B. 用途
C. 送进机构
D. 夹紧机构
【单选题】
___不属于闪光对焊的工艺参数
A. 闪光电流
B. 闪光留量
C. 顶锻压力
D. 工件厚度
【单选题】
闪光对焊机周围 ___m内应无易燃易爆物品,并备有专用的消防灭火器材
A. 5
B. 8
C. 10
D. 15
【单选题】
自由电弧一般经过三种“压缩效应”成为等离子弧,但___不是这三种压缩效应中的一种
A. 机械压缩效应
B. 热收缩效应
C. 磁收缩效应
D. 化学压缩效应
【单选题】
微束等离子弧焊接用的等离子弧型式采用___
A. 间接型弧
B. 非转移型弧
C. 转移型弧
D. 联合型弧
【单选题】
等离子弧切割电源的空载电压一般在___伏之间
A. 60~80
B. 80~90
C. 90~110
D. 150~400
【单选题】
等离子弧切割大厚度割件时的工作气体常用___
A. 氮气
B. 氩气
C. 氢气
D. 氮+氢混合气体
【单选题】
等离子弧切割工作气体氮气的纯度应不低于___
A. 95%
B. 99%
C. 99.5%
D. 99.9%
【单选题】
等离了弧切割不锈钢、铝等厚度可达 ___mm以上
A. 100
B. 150
C. 200
D. 300
【单选题】
___是等离子弧切割设备的控制箱中没有的
A. 程序控制装置
B. 高频振荡器
C. 电磁气阀
D. 高压脉冲稳弧器
【单选题】
等离子弧切割气体的作用不是 ___的
A. 作为等离子弧介质,并压缩电弧
B. 防止钨极氧化烧损
C. 冷却手把
D. 形成隔热层,保护喷嘴不被烧坏
【单选题】
___不属于等离子弧切割工艺参数
A. 气体流量
B. 切割速度
C. 钨极端部到喷嘴的距离
D. 电源极性
【单选题】
___不是转移型等离子弧时产生双弧的原因
A. 钨极与喷嘴不同心过大
B. 钨极内缩量过大
C. 空载电压过高
D. 气体流量太小
推荐试题
【多选题】
Which statement about the communication between interfaces on the same security level is true?___
A. Interfaces on the same security level require additional configuration to permit interinterface communication
B. Configuring interfaces on the same security level can cause asymmetric routing
C. All traffic is allowed by default between interfaces on the same security level
D. You can configure only one interface on a n individual security level
【多选题】
In which two situations should you use in band management? ___
A. when the control plane fails to respond
B. when you require administrator access from multiple locations
C. when you require ROMMON access.
D. where a network device fails to forward packets
E. when multiple ma nagement applications need concument access to the device.
【多选题】
Which two features are supported in a VRF-aware softwar infrastructure before VRF-lite?___
A. multicast
B. fair queuing
C. WCCP
D.
E. IGRP
【多选题】
.Which loS command do you enter to test authentication again a AAA server?___
A. dialer aaa suffix <suffix> password <password>
B. ppp authentication chap pap test
C. test aaa-server authentication dialer group user name <user> password <password>
D. aaa authentication enable default test group tacases
【多选题】
Which two statements about the self zone on a cisco Xone based policy firewall are true?___
A. Multiple interfaces can be assigned to the self zone
B. it supports stateful inspections for multicast traffic
C. zone pairs that include the self zone apply to traffic transiting the device.
D. it can be either the source zone or the destination zone
E. traffic entering the self zone must match a rule
【多选题】
Which type of attack can exploit design flaws in the implementation of an application without ?___
A. DHCP starvation attacks
B. low-rate dos attacks
C. application DDos flood attacks
D. application DDoS flood attacks
E. volume-based DDoS attacks
【单选题】
Which type of firewall can server as the interme diary between a client and a server ?___
A. Stateless firewall
B. application firewall
C. proxy firewall
D. personal firewall
【单选题】
What is the highest security level that can be configured for an interface on an ASA?___
A. 0
B. 50
C. 10
D. 200
【单选题】
Which term refers to the electromagnetic interference that can radiate from network cables?___
A. Gaussian distributions
B. Doppler waves
C. emanations
D. multimode distortion
【单选题】
How does a zone pair handle traffic if the policy de fination of the zone pair is missing?___
A. It inspects all traffic.
B. It drops all traffic.
C. It permits all traffic wihtout logging
D. It permits and logs all traffic
【单选题】
default how does a zone based firewall handle traffic to add from the self zone?___
A. It permits all traffic without inspection
B. It inspects all traffic to determine how it is handled
C. It permits all traffic after inspection
D. It frops all traffic
【单选题】
Which command should beused to ena ble AAA Authentication to determine if a user can access the privilege command level?___
A. aaa authentication enable local
B. aaa authentication enable level=
C. aaa authentication enable method de fault
D. aaa authentication enable defa ult local
【单选题】
On an ASA, the policy indicates that traffic should not be translated is often referred to as which of the following?___
A. NAT zero
B. NAT forward
C. NAT nul
D. NAT allow
【单选题】
Which protocol offers data Integrity encryption, authentication, and anti-replay functions for IPSec VPN?___
A. ESP protocol
B. IKEv3 Protocol
C. AH protoco
D. IKEv1 Protocol
【单选题】
Which component offers a variety of security Solution, including firwall, IF Antivirus and antiphishing features?___
A. Cisco loS router
B. Cisco ASA 5500 Ser ies security appliance
C. Cisco ASA 5500 X series Next Gen Security appliance
D. Cisco 4200 series IPS appliance
【单选题】
Refer to the exhibit, A Network Secur ity administrator check the ASa firewall NAT policy table rith show nat command, which statement is fails?___
A. There are only reverse translation matches for the REAL SERvER object
B. First policy in the Section 1 is a dynamic nat entry defined in the object configuration
C. NAT policy in section 2 is static entry de fined in the object configuration
D. Translation in Section 3 used when a connection does not matches any entries in first two sections
【单选题】
What is true of an aSa in transparent mode ?___
A. It supports OSPF
B. It requires an IP address for each interface
C. It requires a management IP address
D. It allows the use of dynamic NaT
【单选题】
What is the effect of the ip scp server enable command?___
A. It references an access list that allows specific SCP servers
B. It allows the router to initiate requests to an SCP server
C. It allows the router to become an SCP server
D. It adds SCP to the list of allowed copy functions
【单选题】
How can you mitigate attacks in which the attacker attaches more than one vLan tag to a packet?___
A. Assign an access VLAN to every active port on the switch
B. Disable Ether Channel on the switch
C. Explicitly identity each VLAN allowed across the trunk
D.
E. nable transparent VTP on the switch
【单选题】
Which technology can you implement to centrally mitigate potential threats when users on your network download files that might be malicious?___
A. Enable file-reputation services to inspect all files that traverse the company network and block files with low reputation scores
B. Verify that the compa ny IpS blocks all known malicious website
C. Verity that antivirus software is installed and up to date for all users on your network
D. Implement URL filtering on the perimeter firewall
【单选题】
What is the most common implementation of PaT in a standard networked environment?___
A. configuring multiple external hosts to join the self zo ne and to communicate with one another
B. configuring multiple internal hosts to communicate outside of the network using the outside interface IP address
C. configuring multiple internal hosts to communicate outside of the network by using the inside interface IP address
D. configuring an any any rule to enable external hosts to communicate inside the network
【单选题】
Which component of a bYod architecture provides aAa services for endpoint access ?___
A. Integrated Services Router
B. access point
C. ASA
D. Identity Services
E. ngine
【单选题】
You are configuring a NAT rule on a Cisco ASA ,Which description of a mapped interface is true?___
A. It is mandatory for all firewall modes
B. It is optional in routed mode
C. It is optional in transparent mode
D. It is mandatory for ide ntity NAT only
【单选题】
Which description of the use of a private key is true ?___
A. The sender signs a message using the receivers private key
B. The sender signs a message using their private key
C. The sender encrypts a message using the receivers private key
D. The receiver decrypts a n15ssage using the sender's private key
【单选题】
Which mechanism does the FireAMP Connector use to avoid conflicts with other security applications such as antivirus products ?___
A. Virtualization
B. Containers
C. Sandboxing
D.
E. xclusions
【单选题】
Which network to pology de scribes multiple LANS in a gec? ___
A. SOHO
B. MAN
C. pan
D. CAN
【单选题】
Which statement represents a difference between an access list on an aSa versus an access list on a router?___
A. The asa does not support number access lists
B. The aSa does not support standard access list
C. The asa does not ever use a wildcard mask
D. The asa does not support extended access lists
【单选题】
Which command do you enter to verify the status and settings of an iKE Phase 1 tunnel?___
A. show crypto ipsec as output
B. show crypto isakmp
C. show crypto isakmp policy
D. show crypto ipsec transform
【单选题】
Which feature can help a router or switch maintain packet forwarding and protocol states despite an attack or heavy traffic load on the router or switch?___
A. service Policy
B. Control Plane Policing
C. Policy Map
D. Cisco
E. xpress
F. orwarding
【单选题】
Which STP feature can prevent an attacker from becoming the root bridge by immediately shutting down the interface when it receives a BPDU?___
A. root guard
B. Port Fast
C. BPDU guard
D. BPDU filtering
【单选题】
Which technology can best protect data at rest on a user system?___
A. full-disk encryption
B. IPsec tunnel
C. router ACL
D. network IPS
【多选题】
Which two primary security concerns can you mitigate with a BYOD solution ?___
A. schedule for patching the device
B. securing access to a trusted corporate network
C. compliance with applicable policies
D. connections to public Wi-Fi networks
E. device tagging and invento
【多选题】
choose five___
A. MD5————————inserure
B. DES————————insercure
C. SDES———————legacy
D. SHA-1———————legacy
E. HMAC-MD5—————legacy
【多选题】
Which two characteristics of symmetric encryption are true?___
A. It uses digital certificates
B. It requires more resources than asymmetric ancryption
C. It uses the same key to enctypt and decrupt traffic
D. It uses a public key and a pricate key to encrypt and decrypt traffic.
E. It is faster than asymmetric encryption
【多选题】
which two characteristics of PVLAN are true?___
A. Promiscuous porta can communicate with PVLAN ports.
B. Isolated ports cannot communicate with other ports on the same VLAN
C. Community ports have to be a part of the trunk.
D. They require VTP to be enabled in server mode
E. PVLAN ports can be configured as Ether Channel ports
【多选题】
What are two options for running Cisco SDM?___
A. Running SDM from a mobile device
B. Running SDM from within CiscoWorks
C. Running SDM from a router's flash
D. Running SDM from the Cisco web porta
E. Running SDM from a PC
【多选题】
Which two options are the primary deployment modeles for mobile device management?___
A. multisite
B. cloud-based
C. on premises
D. hybrid cloud basedo
E. single site
【多选题】
Drag the recommendation on the left to the Cryptographic algorithms on the right, Options will be used more than once.___
A. Avoid——————————————DES,MD5
B. Legacy——————————————SDES,SHA1,HMAC-MD5
【多选题】
Which two are valid types of vLans using PVLANS ?___
A. Community VLAN
B. Backup VLAN
C. Secondary VLAN
D. Isolated VLAN
E. Isolated VLAN
【多选题】
Which two commands are used to implement Resilient lOS Configuration ___
A. Secure boot-config
B. copy running-config tftp
C. copy flash:ios bin tftp
D. copy running-config startup-config
E. secure boot-image