【单选题】
The opposite meaning of“converging”is______.___
A. diverging
B. opposite
C. diverting
D. closing
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
Which of the following is not included in the ATC clearance? ___
A. Aircraft callsign
B. Flight route
C. Wind direction and speed
D. Clearance limit
【单选题】
“Recycle squawk A0612”means______.___
A. reselect squawk number A0612
B. don’t use A0612
C. who is squawking A0612
D. squawk A0612
【单选题】
“A575”is a name of a route.“A”means_________
A. the order
B. the first kind
C. main south and north direction
D. no special meaning
【单选题】
“FMC”is a system in an aircraft to manage the______.___
A. met message
B. flight data
C. flight pitch
D. flight roll
【单选题】
“Deteriorating weather”means the weather is getting______.___
A. better
B. clear
C. good
D. worse
【单选题】
Azimuth means horizontal______or direction. ___
A. heading
B. direction
C. bearing
D. scale
【单选题】
According to characters and conditions of flights on the route,ATS route is divided into______and______route. ___
A. domestic,international
B. fixed,temporary
C. regional,national
D. civil,military
【单选题】
Fuel______means the quantity of fuel carried by now. ___
A. reminding
B. endurance
C. number
D. total
【单选题】
The opposite meaning of“speedup”is_________
A. slowdown
B. speeddown
C. speedlow
D. slowby
【单选题】
Pilot turns on squawk______to request a squawk number. ___
A. 3000
B. 3500
C. 4000
D. 2000
【单选题】
First______assistance means doctor and ambulance in an emergency condition. ___
A. emergency
B. priority
C. aid
D. help
【单选题】
When somebody is reported hurt on board,maybe it will need______assistance on arrival. ___
A. fire-cart
B. medical
C. police
D. wheelchair
【单选题】
In emergency descent procedure,the pilot should turn right______out of the route while descending. ___
A. 40°
B. 30°
C. 20器
D. 15°
【单选题】
管制员在对空指挥过程中,越是繁忙的时候,语速应___
A. 保持平稳,避免频繁重复指令
B. 尽量快些,才能指挥更多飞机
C. 降低语速,避免口误
D. 时快时慢,引起机组的注意
【单选题】
According to ICAO,a standard holding pattern should all turn to the______.___
A. right
B. west
C. left
D. east
【单选题】
The standard altimeter setting is______inhpa. ___
A. 1013.20062
B. 1010.10062
C. 29.92002
D. 30.10002
【单选题】
2500f/m rate of vertical speed is equal to______.___
A. 10m/s
B. 15m/s
C. 20m/s
D. 25m/s
【单选题】
陆空通话时,什么时候推荐使用“IMMEDIATELY(立即)”这个词:___
A. 相对飞行穿高度时
B. 天气差时,担心自己会忘记某个正在改变高度的动态
C. 飞机多时,为了节省精力
D. 在紧急情况下,用于冲突解脱时
【单选题】
Standard rate for a turning is______degrees per second. ___
A. 4
B. 6
C. 3
D. 2
【单选题】
What is the best course of action for a pilot to follow when thunderstorms are observed along the route of flight? ___
A. Fly below the thunderstorms
B. Climb over the thunderstorms
C. Disregard the thunderstorms
D. Take any action to avoid all thunderstorms
【单选题】
The subdivision of frequencies is______MHZ. ___
A. 0.025
B. 0.035
C. 0.02
D. 0.015
【单选题】
Aeronautical chart is divided into two categories,______. ___
A. Aeronautical map and special type of aeronautical chart
B. En-route chart and approach chart
C. Area chart and standard instrument arrival and departure chart
D. Aerodrome chart and area chart
【单选题】
Aircraft are required to comply with ATC instructions within______.___
A. advisory airspace
B. domestic airspace
C. controlled airspace
D. international airspace
【单选题】
Amendments to the initial clearance will be issued at anytime an air traffic controller deems such action necessary to______.___
A. avoid possible confliction between aircraft
B. correct the previously issued clearance
C. cancel the flight plan
D. expedite the traffic
【单选题】
研究表明,当耳机话筒的位置距离嘴( )英寸且稍微偏下时,传输的声音质量最佳。(注:1英寸=2.54CM)___
A. 0.25-0.5
B. 0.75-1
C. 1.25-1.5
D. 1.75-2
【单选题】
“I want to divert to shanghai” is equal to______.___
A. I want to our destination Shanghai
B. I want to overfly Shanghai
C. I want to alternate to land at Shanghai
D. I want to call Shanghai control
【单选题】
When an aircraft is being subjected to unlawful interference, the pilot should try to notify _______ of this fact.___
A. the appropriate ATC units
B. company
C. the passengers on board
D. air attendants
【单选题】
When pilot say“Did you pick it upon your screen?”,that means______.___
A. did you pick up your screen?
B. did you see it on your screen?
C. did your screen pick me up?
D. did you change your radar?
【单选题】
ATC clearance does not contain______.___
A. clearance limit
B. altitude data
C. route of flight
D. flight direction
【单选题】
When pilot sets an altimeter setting to a QNH,that will indicate_________
A. flight level
B. altitude
C. height
D. safety level
【单选题】
When pilots set a pressure of 29.92 in mercury to indicate_________
A. altitude
B. height
C. flight level
D. safety level
【单选题】
管制员还应当对管制指令当中的不同内容进行适当的排序,相对重要的内容应当排列在管制指令的 ( )位置___
A. 前面
B. 中间
C. 尾部
D. 以上都可以
【单选题】
When Beijing time is 0801,Zulu time should be______.___
A. 2001
B. 1
C. 601
D. 1601
【单选题】
Emergency frequency is______.___
A. 121.5MHZ
B. 120.5MHZ
C. 121MHZ
D. 119.0MHZ
【单选题】
“PAN” is the international RTF______signal___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
“MAYDAY” is the international RTF______signal.___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
According to ICAO definition, a condition concerning the safety of an aircraft or other vehicle or of some person on board or within sight but which does not require immediate assistance is _______ .___
A. urgency
B. dangerous
C. emergency
D. distress
【单选题】
Which SSR Code is not right?___
A. 7020
B. 8025
C. 6060
D. 4021
【单选题】
______is the accepted standard for worldwide time signal broadcast used for aviation.___
A. GMT
B. LT
C. UTC
D. SST
【单选题】
_____means the level is measured in 1013.2 pha___
A. Level
B. Height
C. Altitude
D. Flight level
推荐试题
【单选题】
螺旋机构传动精度高,工作平稳,无噪音,___,能传递较大扭矩。
A. 易于自锁
B. 效率高
C. 易冲击
D. 速度高
【单选题】
能承受较大冲击载荷的轴承是___。
A. 滑动轴承
B. 滚动轴承
C. 滚子轴承
D. 推力轴承
【单选题】
轴瓦与轴承座盖的装配,厚壁轴瓦以___为基准修刮轴瓦背部。
A. 芯轴
B. 座孔
C. 与其相配的轴
D. 检验棒
【单选题】
内柱外锥式轴承装配修刮外套内锥孔,其接触斑点为___/(25mmX25mm)。
A. 4~8点
B. 8~12点
C. 12~16点
D. 25点以上
【单选题】
以主轴为基准,配制内柱外锥式轴承内孔,后轴承以工艺套支承,以保证前后轴承___。
A. 平行度
B. 对称度
C. 圆柱度
D. 同轴度
【单选题】
当环境温度高于或等于38C时,滚动轴承不应超过___C°
A. 65
B. 80
C. 38
D. 50
【单选题】
滚动轴承内孔为基准孔,即基本偏差为零,公差带在零线的___。
A. 上方
B. 下方
C. 上下对称
D. 随使用要求定
【单选题】
单列向心球轴承在代号中用___表示。
A. 1
B. 2
C. 0
D. 3
【单选题】
滚动轴承201向心球轴承孔径为___。
A. 10mm
B. 12mm
C. 5mm
D. 17mm
【单选题】
轴的两端支承点用轴承盖单向固定,为了避免轴受热伸长使轴承卡住,在另一轴承外圈与端盖间留有间隙,其间隙为___。
A. 0~0.5mm
B. 0.5~1mm
C. 1~1.5mm
D. 2mm
【单选题】
向心推力滚子轴承若采用轴冷缩法装配,装配温度不得低于___。
A. 0℃
B. -40℃
C. -60℃
D. -80℃
【单选题】
右轴承双向轴向固定,左端轴承可随轴游动,工作时不会发生___。
A. 轴向窜动
B. 径向移动
C. 热伸长
D. 振动
【单选题】
为了保证滚动轴承工作时有热胀余地,在用轴的两个轴承中,必须有一个外圈(或内圈)可以在热膨胀时产生___移动,以免使轴承咬住。
A. 轴向
B. 径向
C. 定向
D. 反向
【单选题】
接触式密封装置,常因接触处滑动摩擦造成动力损失和磨损,故用于___。
A. 高速
B. 低速
C. 重载
D. 轻载
【单选题】
下列密封装置中,属于接触式密封装置的是___。
A. 毡圈
B. 间隙式
C. 迷宫式
D. 垫圈式
【单选题】
滚动轴承严重磨损后,采用___的方法修复,以保证机器正常运转。
A. 焊解
B. 镀铬
C. 更换新轴承
【单选题】
滚动轴承修理,当锥形孔内圈轴承间隙过大时,一般采用___的方法来减小间隙。
A. 焊解
B. 镀铬
C. 调节轴向位置
D. 镀镍
【单选题】
轴承装在轴上和外壳内的游隙叫___游隙。
A. 原始
B. 配合
C. 工作
D. 径向
【单选题】
滚动轴承调整游隙的方法是将内外圈作适当的___相对位移。
A. 轴向
B. 径向
C. 同向
D. 方向
【单选题】
预紧是在轴承内外圈上,给予一定的轴向预负荷,消除了内外圈与滚动体的游隙,产生了初始的___。
A. 接触弹性变形
B. 塑性变形
C. 弯曲变形
D. 挤压变形
【单选题】
滚动轴承预紧的目的是为了提高___精度。
A. 轴承
B. 轴的旋转
C. 轴承寿命
D. 轴的刚度
【单选题】
轴承内圈与主轴,轴承外圈与箱体孔装配时,采用定向装配法适用于___。
A. 精度要求较低的主轴
B. 精度要求一般的主轴
C. 精度要求较高的主轴
D. 重载低速的主轴
【单选题】
定向装配的目的是为了提高主轴的___。
A. 装配精度
B. 回转精度
C. 工作精度
D. 形状精度
【单选题】
间隙越小,选择润滑油的粘度应越___。
A. 高
B. 低
C. 硬
D. 软
【单选题】
冲击振动的载荷,将形成瞬间极大的压强,故均应采用粘度___的润滑油。
A. 较大
B. 较小
C. 特别大
D. 特别小
【单选题】
在麻花钻上开分屑糟主要应用在___。
A. 铸铁
B. 胶木
C. 铝
D. 钢
【单选题】
修磨钻头顶角,磨成双重或三重顶角是为加工___。
A. 铜
B. 结构钢
C. 铸铁
D. 碳素工具钢
【单选题】
钻精度要求较高的铸铁孔时,应选用___冷却液。
A. 猪油
B. 菜油
C. 煤油
D. 硫化切削油
【单选题】
钻孔时,选择切削用量的基本原则是在允许范围内,尽量先选较大的___。
A. 吃刀深度
B. 进给量
C. 切削速度
D. 切削工具
【单选题】
在孔快要钻穿时,必须减少___,钻头才不易损坏。
A. 进给量
B. 吃刀深度
C. 切削速度
D. 润滑油
【单选题】
钻孔精度较低,尺寸精度只能达到___。
A. IT6~IT7
B. IT8~IT9
C. IT10~IT11
D. IT12~IT13
【单选题】
钻小孔,钻削直径小于1mm的孔时,转速应达到___。
A. 800~1000r/min
B. 1000~1500r/min
C. 1500~3000r/min
D. 10000~15000r/min
【单选题】
钻相交孔时,对于不等径相交孔应先钻___。
A. 大孔
B. 小孔
C. 等径孔后扩大孔
D. 大小孔没先后
【单选题】
标准群钻圆弧刃上各点的前角___。
A. 比麻花钻大
B. ,比麻花钻销
C. 与麻花钻相等
D. 为一定值
【单选题】
薄板群钻,外缘处磨出锋利的两个刀尖,与钻心刀尖相差仅___,形成三尖。
A. 0.1~0.5mm
B. 0.5~1.5mm
C. 1.5~2.5mm
D. 2.5~3.5mm
【单选题】
钻铸铁钻头为了增大容屑空间,钻头后刀面磨去一块,即形成___的第二重后角。
A. 30°
B. 43°
C. 45°
D. 60°
【单选题】
钻精孔钻头,两主切削修磨要对称,两刃径向摆动差应小于___。
A. 0.05mm
B. 0.1mm
C. 0.2mm
D. 0.3mm
【单选题】
扩孔时的吃刀深度为___。
A. D/2
B. D/2
C. (D-D)/2
D. (D+D)/2
【单选题】
铰铸铁零件孔时加煤油冷却,会引起孔径缩小,最大收缩量为___mm.
A. 0.02~0.04
B. 0.05~0.1
C. 0.002~0.004
D. 0.004~0.006
【单选题】
旋转机械产生振动的原因有:转子不平衡量过大;轴系对中不良;转子结构件松动和___等多种。
A. 装配精度高
B. 加工精度高
C. 平衡实验合格
D. 轴承系统失稳