【单选题】
电气操作人员（电工）应穿戴由绝缘材料制成的___（最小）的电力工人靴和手套。
A. 20KV
B. 30KV
C. 40KV
D. 50KV
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
电缆通道及直埋电缆线路工程应严格按照相关标准和设计要求施工，并同步进行___，非开挖工艺的电缆通道应进行三维测绘。应在投运前向运维部门提交竣工资料和图纸。
A. 施工验收
B. 设计验收
C. 竣工验收
D. 竣工测绘
【单选题】
投运___年及以上的非地下变电站接地网，应定期开挖（间隔不大于 5 年），抽检接地网的腐蚀情况，每站抽检 5～8 个点。铜质材料接地体地网整体情况评估合格的不必定期开挖检查。
A. 10
B. 11
C. 12
D. 13
【单选题】
为防止地网中的大电流流经电缆屏蔽层，应在开关场二次电缆沟道内沿二次电缆敷设截面积不小于___的专用铜排（缆）。
A. 50mm2
B. 100mm2
C. 150mm2
D. 200mm2
【单选题】
专用铜排（缆）的一端在开关场的每个就地端子箱处与主地网相连，另一端在保护室的电缆沟道入口处与主地网相连，铜排不要求与___绝缘。
A. 电缆井
B. 电缆沟
C. 电缆支架
D. 电缆隧道
【单选题】
___系统应采用阻燃电缆。两组及以上蓄电池组电缆，应分别铺设在各自独立的通道内，并尽量沿最短路径敷设。在穿越电缆竖井时，两组蓄电池电缆应分别加穿金属套管。对不满足要求的运行变电站，应采取防火隔离措施。
A. 直流电源
B. 交流电源
C. 直流
D. 交流
【单选题】
变压器中、低压侧至配电装置采用电缆连接时，应采用___电缆；运行中的三相统包电缆，应结合全寿命周期及运行情况进行逐步改造。
A. 三芯
B. 单芯
C. 10kV
D. 35kV
【单选题】
全电缆线路___采用重合闸，对于含电缆的混合线路应根据电缆线路距离出口的位置、电缆线路的比例等实际情况采取停用重合闸等措施，防止变压器连续遭受短路冲击。
A. 一般
B. 偶尔
C. 禁止
D. 可以
【单选题】
与既有地下管线水平铺设时，φ200mm 以上的管线，净距应为最大扩孔径的 2 倍以上；φ200mm 以下的管线，净距不得小于___m。
A. 0.5
B. 0.6
C. 0.7
D. 0.8
【单选题】
钻杆的曲率半径应由钻杆的弯曲强度值确定。根据工程实践经验，一般情况下钻杆弯曲半径为___以上（D为钻杆外径）。
A. 1000D
B. 1100D
C. 1200D
D. 1300D
【单选题】
导向孔钻进时，造斜段测量计算频率一般情况每___，直线段测量计算频率一般每根钻杆一次；测量参数应符合设计轨迹要求，且应按下列要求进行数据记录：
A. 0.5～1.0m/次
B. 1.0～1.5m/次
C. 1.5～2.0m/次
D. 2.0～2.5m/次
【单选题】
造斜段顶进时，一次顶进长度宜小于___，同时应观察延伸长度顶角变量，顶角变量应符合钻杆极限弯曲强度要求，采取分段施钻，使延伸长度顶角应变化均匀。
A. 0.5～1.0m
B. 1.0～1.5m
C. 1.5～2.0m
D. 2.0～2.5m
【单选题】
排水管道工程检测验收，轴线偏差小于___、管内底高程偏差小于（）。管道严密性试验和允许渗水量应按《给水排水管道工程施工及验收规范》GB50268执行。
A. ±200mm ±100mm
B. ±100mm ±200mm
C. ±100mm ±50mm
D. ±50mm ±100mm
【单选题】
定向钻铺管施工前应进行___。工程勘察应符合《岩土工程勘察规范》GB50021、《岩土工程勘察规范》DBJ13-84和《城市地下管线探测技术规程》CJJ61的规定。
A. 现场勘察
B. 工程勘察
C. 现场交底
D. 技术交底
【单选题】
工程勘察应包括工程地质、___、地形、地貌、地面建（构）筑物及既有地下管线探测、管线铺设路由勘察等。
A. 管线工程平面图
B. 水文地质
C. 既有管线地下管网图
D. 工程技术要求
【单选题】
与既有地下管线水平铺设时，φ200mm 以上的管线，净距应为最大扩孔径的___倍以上；φ200mm 以下的管线，净距不得小于0.6m。
A. 2
B. 3
C. 4
D. 5
推荐试题
【单选题】
A vSphere content library administrator is attempting to unpublish the content library, but the option is grayed out as shown in the Exhibit. Which statement identifies the reason for not being able to unpublish? ___
A. The content library is optimized for syncing over HTTP.
B. A synchronization operation is in progress with this content library.
C. There are active subscriptions on this content library.
D. Underlying storage for this content library is not accessible.
【单选题】
Assuming a mirrored (RAID-1) object configuration, how many hosts must contribute storage in a non-stretched VMware vSAN cluster to satisfy the “Number of failures to tolerate” policy option?“n” is the desired “Number of failures to tolerate” value for all options.___
A. 2n+2
B. 2n
C. 2n+1
D. 3n
【单选题】
An administrator must change the statistics level for short-term performance monitoring and wants to collect metrics for all counters, excluding minimum and maximum rollup values. What would be the statistics level?___
A. Level 3
B. Level 1
C. Level 2
D. Level 4
【单选题】
In a vSphere environment, two resource pools are created as shown in the Exhibit. Each VM is configured with 1 GB of memory. When the administrator tried to power on VM3, the operation failed. What action in the resource pool settings will allow VM3 to power on successfully?___
A. Deselect Expandable Memory Reservation
B. Increase Memory Reservation
C. Deselect Expandable CPU Reservation
D. Increase the CPU Reservation
【单选题】
Which network is used by vSphere HA when VMware vSAN is enabled?___
A. Management network
B. vSphere Replication network
C. vMotion network
D. VSAN network
【单选题】
Which statement is correct when migrating from a Windows vCenter Server to the vCenter Server Appliance 6.5?___
A. Migration deployments do not migrate local OS users from the source vCenter Server.
B. Migration deployments support DHCP on the source vCenter Server.
C. Migration deployments allow the source vCenter Server to remain powered on afterwards.
D. Migration deployments support custom ports for all services on the source vCenter Server.
【单选题】
How can failback of a recovered virtual machine in vSphere Replication be performed?___
A. No action required, because failback is automatically performed to the source site.
B. Configure a new replication in the reverse direction at the target site.
C. Disable or Stop the virtual machine replication on the source site.
D. Power off and unregister the virtual machine on the target site.
【单选题】
After upgrading the vSphere infrastructure and VMware Tools to version 6.5, the “Upgrade VM Compatibility” option is grayed out in the vSphere Web Client. (See Exhibit.) What must the administrator do to enable the VM compatibility upgrade?___
A. VMware Tools should be upgraded last.
B. Restart the ESXi server.
C. Uninstall VMware Tools.
D. Power off the virtual machine.
【单选题】
What availability mode does vCenter HA provide?___
A. Active-Passive
B. Active-Standby
C. Active-Active
D. Load-balanced
【单选题】
In which scenario will vSphere DRS balance resources when set to Fully Automated?___
A. Hosts with only shared storage
B. Hosts are part of a vSphere HA cluster
C. Power Management is set to Balanced on hosts
D. Hosts with shared or non-shared storage
【单选题】
What VMware technology can be used to move physical servers to the vSphere infrastructure?___
A. VMware vMotion
B. VMware Converter
C. VMware vCenter Server
D. OVF transport
【单选题】
Upgrading vCenter Server with Microsoft SQL database fails with the following error message: The DB User entered does not have the required permissions needed to install and configure vCenter Server with the selected DB. Please correct the following error(s): %sWhat could cause this error?___
A. incorrect ports open on SQL Server
B. incorrect database on the SQL server
C. incorrect compatibility mode on the SQL server
D. incorrect permission on SQL Server database
【单选题】
What is a potential downside of having more than four paths per datastore?___
A. limits the storage protocols
B. increases storage latency for VM
C. limits the path selection policies
D. limits the number of LUNs per host
【单选题】
Which feature facilitates the sharing of templates via vCenter Server?___
A. Content Library
B. OVF
C. folders
D. vApp
【单选题】
A vSphere Administrator is in the process of configuring replication for a virtual machine, but is not able to select the Recovery Point Objective (RPO) value of 5 minutes. Which statement could explain why the RPO value cannot be lower than 15 minutes?___
A. The OS quiescing option is selected for Replication options.
B. The virtual machine hardware version is not compatible.
C. The target and source sites use different types of datastores.
D. The target and source sites are not using VMFS 6.0 datastore.
【单选题】
What advanced parameter defines a custom isolation IP address for a vSphere HA cluster?___
A. das.usedefaultisolationaddress
B. das.isolationshutdowntimeout
C. fdm.isolationpolicydelaysec
D. das.isolationaddress
【单选题】
Which method is supported for backing up the virtual machine that contains vCenter Server?___
A. differential
B. incremental
C. full image
D. individual disks
【单选题】
A vSphere Administrator must ensure that a user is able to view and manage the system configuration in vSphere Web Client. In the vCenter Single Sign-On domain, which group should the user be a part of?___
A. SystemConfiguration.BashShellAdministrators
B. ComponentManager. Administrators
C. Administrators
D. SystemConfiguration.Administrators
【单选题】
What is the minimum number of hosts that must contribute capacity to a non-ROBO single site VMware vSAN cluster?___
A. 1
B. 64
C. 3
D. 2
【单选题】
Which guest operating system supports PVRDMA?___
A. Windows (32-Bit)
B. Linux (32-Bit)
C. Windows (64-Bit)
D. Linux (64-Bit)
【单选题】
What is the correct way to replace the certificate on an existing vCenter Server that is part of a vCenter HA configuration?___
A. Put the vCenter HA in Maintenance mode, replace the certificate, exit Maintenance mode.
B. Shut down Passive and Witness nodes and replace the certificate on the Active node.
C. Remove the Passive and Witness nodes, replace the certificate, reconfigure the cluster.
D. Replace the certificate while all nodes are participating in the cluster.
【单选题】
The vSphere Data Protection performance analysis results in the “Conditionally Passed” status. What can cause this condition?___
A. The results did not meet the minimum performance expectations.
B. The read, write, and seek tests were successful.
C. The read and write tests were successful but the seek test failed.
D. The read and write tests were successful but the seek test skipped.
【单选题】
A vSphere Administrator wants to reserve 0.5 Gbps for virtual machines on each uplink on a disturbed switch that has 10 uplinks. What is the quota that should be reserved for the network resource pool?___
A. 10 Gbps
B. 5 Gbps
C. 100 Gbps
D. 0.5 Gbps
【单选题】
A vSphere administrator manages a cluster which includes critical and non-critical virtual machines. The cluster requires different permissions for contractors and non-contractors. How can the administrator exclude the contractor group from some of the critical VMs?___
A. Apply permission for both contractors and non-contractors on the cluster level.
B. Apply permission for both contractors and non-contractors on the cluster level. Remove permission on the critical VMs for contractors.
C. Remove permission for contractors on the cluster level. Apply permission on the critical VMs for noncontractors.
D. Apply permission for both contractors and non-contractors on the VMs. Remove permission on the critical VMs for contractors.
【单选题】
In an ESXi 6.5 cluster only "NFS datastore has running or registered virtual machines" returns. A vSphere HA cluster with four hosts has admission control configured to tolerate one host failure. Which statement is true if a fifth host is added?___
A. CPU and Memory capacity will be set to 50%.
B. CPU and Memory capacity will be set to 30%.
C. CPU and Memory capacity will be set to 25%.
D. CPU and Memory capacity will be set to 20%.
【单选题】
Which command can be run to troubleshoot connectivity problems with vmkernal network interfaces?___
A. esxcli network
B. vmkping
C. net-status
D. vicfg-vmknic
【单选题】
What counter should an administrator check to determine if a virtual machine is ballooning?___
A. swapinRate
B. vmmemctltarget
C. swapped
D. vmmemctl
【单选题】
By default, how often is the vCenter vpx user password automatically changed?___
A. 15 days
B. 60 days
C. 30 days
D. 45 days
【单选题】
Which metric in the Exhibit would identify high latency for a virtual machine operating system?___
A. QAVG/cmd
B. KAVG/cmd
C. DAVG/cmd
D. GAVG/cmd
【单选题】
What VM Monitoring setting would ensure that the failure interval for a virtual machine is defined as 120 seconds?___
A. High
B. Normal
C. Low
D. Medium
【单选题】
The business managers have asked the IT administrator to ensure configuration compliance in the vSphere infrastructure. The IT administrator wants to use Host Profiles to accomplish this, but is unable to do so. Why is the administrator unable to use Host Profiles?___
A. The infrastructure uses a vSphere Standard license.
B. The infrastructure has servers with various CPU families.
C. The user has only the “Administrator” role.
D. Host Profiles apply only to storage settings.
【单选题】
What is the result of a “Consolidate” action on a virtual machine?___
A. All snapshots on the virtual machines will be deleted.
B. The virtual machine will be reverted to its last snapshot.
C. Redundant delta disks will be combined and deleted.
D. A new snapshot with memory state will be created.
【单选题】
A Telco customer is implementing NFV using vSphere as the virtualization platform. Which feature can help achieve a high packet rate with lower CPU consumption?___
A. Network I/O Control
B. SplitRX
C. ERSPAN
D. LACP
【单选题】
What is the VMware-recommended best practice for Fibre Channel zoning?___
A. soft zoning
B. single-initiator-multiple-target zoning
C. single-initiator zoning
D. single-initiator-single-target zoning
【单选题】
How can a vSphere administrator ensure that a set of virtual machines run on different hosts in a DRS cluster?___
A. Use a VM-Host affinity rule.
B. Add the VMs to a vApp.
C. Use a VM-VM affinity rule.
D. Place the VMs in different folders.
【单选题】
vCenter Server Appliance Instance can be backed up using which Client Interface?___
A. vSphere Client Interface
B. vSphere Web Client Interface
C. VMware Host Client Interface
D. Virtual Appliance Management Interface
