【多选题】
安全阀常见的故障有___。
A. 密封面发生泄漏
B. 安全阀达不到全开状态
C. 阀瓣振荡
D. 安全阀不能迅速关闭
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
ABCD
解析
暂无解析
相关试题
【多选题】
下列选项中,属于离心泵泵内损失的是___。
A. 摩擦损失
B. 水力损失
C. 机械损失
D. 容积损失
【多选题】
按阀门结构分类,阀门可以分为___。
A. 闸阀
B. 截止阀
C. 单向阀
D. 蝶阀
【多选题】
化工生产上属于定型设备的有___。
A. 吸收塔
B. 再生塔
C. 容器
D. 换热器
【多选题】
压缩机喘振的影响因素是___。
A. 压缩机的转速
B. 管网的容积
C. 压缩机进口压力
D. 压缩机功率
【多选题】
换热管及管板胀接工艺有等几种。___。
A. 机械胀接
B. 液袋胀接
C. 爆破胀接
D. 橡胶胀接
【多选题】
通过换热器型号BES700-1.27/1.61-155-6/19-4可以获得以下信息。___。
A. B指封头管箱, E指单程壳体,S指钩圈式浮头
B. 700是公称直径,mm;1.27/1.61是指管/壳程公称压力, Mpa
C. 155是指公称换热面积, m2;6/19 是指换热管长度m,及换热管外径,mm
D. 管程数为4,壳程数为1
【多选题】
化工管路保温保冷的目是___ 。
A. 减少热损和冷损
B. 增大损耗量
C. 改善劳动环境
D. 没什么作用和目的
【多选题】
废热锅炉投用后,下列___指标是锅炉水控制指标。
A. 电导率
B. pH值
C. 磷酸根
D. 钠离子
【多选题】
以下图所示,1、2、3分别指离心泵哪个部位___。
A. 轴承
B. 密封
C. 呼吸阀
D. 油视镜
【多选题】
空气冷却器的风机风量调节手段有___。
A. 调节叶片倾角
B. 风机的转速
C. 百叶窗的开启程度
D. 管束的多少
【多选题】
离心泵的主要性能是通过___ 等表示的。
A. 流量
B. 扬程
C. 功率
D. 效率
【多选题】
进汽温度过高和过低使汽轮机___。
A. 振动
B. 叶片冲刷
C. 叶片断裂
D. 零部件互相碰撞
【多选题】
转子发生工频振动的原因有___。 
A. 转子不平衡   
B. 油膜振荡   
C. 轴承无紧力
D. 对中不良
【多选题】
下列操作步骤中属于往复式压缩机有___。 
A. 润滑油系统的试车       
B. 电动机试车     
C. 压缩机无负荷试车     
D. 压缩机负荷试车
【多选题】
调节阀依气动调节阀在有信号作用时阀芯的位置可分为___两种。 
A.  、气关式    
B.  气开式 
C. 电动阀  
D.  闸阀
【多选题】
固定板式换热器有___的特点。
A. 结构简单
B. 成本低
C. 适用于壳体压力高的场所
D. 适用于壳体压力低的场所用介质
【多选题】
压力容器无损检测中射线检测对___缺陷比较有效。
A.  、裂纹    
B.  气孔 
C. 夹渣  
D. 弧坑
【多选题】
硫封罐进口液硫管线堵塞主要判断方法有___
A. 观察硫封罐溢流口液硫流动情况    
B. 检查管线伴热情况 
C. 观察系统压力是否有升高现象  
D. 观察硫冷器是否有剧烈震动现象
【多选题】
鼓风机故障的现象有___。
A.  、风量不稳定    
B.  风压不稳定 
C. 风量中断  
D. 出口压力高
【多选题】
浮头式换热器由___组成。
A. 管束
B. 浮头
C. 壳体
D. 头盖
【多选题】
阀门加油的作用是___。
A.  、保证润滑效果    
B.  有利于开关 
C. 防止泄漏  
D. 防止腐蚀
【多选题】
浮头式换热器的结构复杂,主要等零部件有___。
A.  、防冲板   
B.  挡板
C. 浮头管板  
D. 钩圈
【多选题】
U型管换热器具有___特点。
A. 弹性小
B. 热补偿性能好
C. 管程流速低
D. 承压能力高
【多选题】
活塞式压缩机的气阀,检修后进行试漏试验,不应选用___。
A.  、水   
B.  汽油
C. 煤油
D. 柴油
【多选题】
按工作原理,汽轮机可分为___两种。
A.  、凝汽式    
B.  冲动式
C. 反动式  
D. 背压式
【多选题】
与管壳式换热器相比板式换热器有哪些特点___。
A. 传热系数高    
B. 重量轻
C. 占地面积小  
D. 清洗方便
【多选题】
机械型疏水阀分类有___。
A.  、自由浮球式    
B.  自由浮球式
C. 杠杆浮球式  
D. 杠杆浮球式
【多选题】
我们装置中以下风机属于罗茨风机是___。
A.  、氧化风机    
B.  焚烧炉风机
C. 罐顶气风机  
D. 液硫池增压风机
【多选题】
以下选项属于管壳式换热器是___。
A.  、板式换热器    
B.   U型管式换热器
C. 浮头式换热器  
D. 固定管板式换热器
【多选题】
润滑“五定“是指___。
A. 定人  
B. 定质,定量
C. 定点  
D. 定时
【多选题】
废热锅炉完全烧干时补水的不正确处理方法是___
A. 可以立即补水    
B. 炉膛熄火以后就可补水
C. 等出口温度降至100℃以下再补水  
D. 等出口温度降至常温才能补水
【多选题】
环型填料有___
A.  、拉西环  
B.   鲍尔环
C. 改进鲍尔环  
D. 阶梯环
【多选题】
关于屏蔽泵说法正确的是___。
A. 输送液体不会泄漏  
B. 严禁空载运行
C. 可以允许逆向运转  
D. 电机与泵是一体
【多选题】
风机启动后无法提升压力___。
A. 电机反转  
B. 电机转速慢
C. 风机进口阀芯脱落  
D. 风机出口压力表失灵
【多选题】
液硫泵(双螺杆泵)启动注意事项有哪些___。
A. 启动时必须保证出口关闭  
B. 严禁长时间干转
C. 严禁反转  
D. 不允许依靠调节出口阀大小来满足小流量工况
【多选题】
引起法兰泄漏的原因有___。
A. 垫片选用不当
B. 法兰面破损
C. 螺栓紧力不匀
D. 介质太脏
【多选题】
换热器管束有___排列方式。
A. 等过三角形
B. 正方形
C. 正方形错列
D. 同心圆形排列
【多选题】
压力容器按其功能分为___。
A. 反应压力容器
B. 换热压力容器
C. 分离压力容器
D. 储运压力容器
【多选题】
在高温条件下,设备发生硫化氢腐蚀的类型是___。
A. 硫腐蚀
B. 氢腐蚀
C. 硫化氢腐蚀
D. 二氧化硫
【多选题】
泵启动后提不上量的原因___。
A. 进口管堵塞
B. 进口阀芯脱落
C. 进口管存有气体
D. 进口罐液面低于泵进口
推荐试题
【单选题】
which technology cloud be used on top of an MPLS VPN to add confidentiality ?___
A. IPsec
B. 3DES
C. AES
D. SSL
【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
【单选题】
You have just deployed SNMPv3 in your environment, Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request?___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port?___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF