【单选题】
46.将接触器KMl的常开触点串联到接触器KM2线圈电路中的控制电路能够实现___
A. KMl控制的电动机先停止,KM2控制的电动机后停止的控制功能
B. KM2控制的电动机停止时,KMl控制的电动机也停止的控制功能
C. KM2控制的电动机先启动,KMl控制的电动机后启动的控制功能
D. KMl控制的电动机先启动,KM2控制的电动机后启动的控制功能
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
D
解析
暂无解析
相关试题
【单选题】
47.位置控制就是利用生产机械运动部件上的___与位置开关碰撞来控制电动机的工作状态的。
A. 挡铁
B. 红外线
C. 按钮
D. 超声波
【单选题】
48.下列器件中,不能用作三相异步电动机位置控制的是___。
A. 磁性开关
B. 行程开关
C. 倒顺开关
D. 光电传感器
【单选题】
49.下列不属于位置控制线路的是___。
A. 走廊照明灯的两处控制电路
B. 龙门刨床的自动往返控制电路
C. 电梯的开关门电路
D. 工厂车间里行车的终点保护电路
【单选题】
50.下列属于位置控制线路的是___。
A. 走廊照明灯的两处控制电路
B. 电风扇摇头电路
C. 电梯的开关门电路
D. 电梯的高低速转换电路
【单选题】
51.三相异步电动机能耗制动时___中通入直流电。
A. 转子绕组
B. 定子绕组
C. 励磁绕组
D. 补偿绕组
【单选题】
52.三相异步电动机能耗制动时,机械能转换为电能并消耗在___回路的电阻上。
A. 励磁
B. 控制
C. 定子
D. 转子
【单选题】
53.三相异步电动机采用___时,能量消耗小,制动平稳。
A. 发电制动
B. 回馈制动
C. 能耗制动
D. 反接制动
【单选题】
54.三相异步电动机能耗制动的过程可以用___来控制。
A. 电流继电器
B. 电压继电器
C. 速度继电器
D. 热继电器
【单选题】
55.三相异步电动机能耗制动的过程可以用___来控制。
A. 电压继电器
B. 电流继电器
C. 热继电器
D. 时间继电器
【单选题】
56.三相异步电动机能耗制动的控制线路至少需要___个按钮。
A. 2
B. 1
C. 4
D. 3
【单选题】
57.三相异步电动机反接制动时,___绕组中通入相序相反的三相交流电。
A. 补偿
B. 励磁
C. 定子
D. 转子
【单选题】
58.三相异步电动机的各种电气制动方法中,能量损耗最多的是___。
A. 反接制动
B. 能耗制动
C. 回馈制动
D. 再生制动
【单选题】
59.三相异步电动机反接制动,转速接近零时要立即断开电源,否则电动机会___。
A. 飞车
B. 反转
C. 短路
D. 烧坏
【单选题】
60.三相异步电动机倒拉反接制动时需要___。
A. 转子串人较大的电阻
B. 改变电源的相序
C. 定子通入直流电
D. 改变转子的相序
【单选题】
61.三相异步电动机电源反接制动的过程可用___来控制。
A. 电压继电器
B. 电流继电器
C. 时间继电器
D. 速度继电器
【单选题】
62.二三相笼型异步电动机电源反接制动时需要在___中串人限流电阻。
A. 卣流回路
B. 控制回路
C. 定子回路
D. 转子回路
【单选题】
63.三相异步电动机再生制动时,将机械能转换为电能,回馈到___。
A. 负载
B. 转子绕组
C. 定子绕组
D. 电网
【单选题】
64.三相异步电动机再生制动时,转子的转向与旋转磁场相同,转速___同步转速。
A. 小于
B. 大于
C. 等于
D. 小于等于
【单选题】
65.三相异步电动机的各种电气制动方法中,最节能的制动方法是___。
A. 再生制动
B. 能耗制动
C. 反接制动
D. 机械制动
【单选题】
66.三相异步电动机再生制动时,定子绕组中流过___。
A. 高压电
B. 直流电
C. 三相交流电
D. 单相交流电
【单选题】
67.同步电动机可采用的启动方法是___。
A. 转子串频敏变阻器启动
B. 转子串三级电阻启动
C. Y-A启动法
D. 异步启动法
【单选题】
68.同步电动机可采用的启动方法是___。
A. 转子串三级电阻启动
B. 转子串频敏变阻器启动
C. 变频启动法
D. Y-A启动法
【单选题】
69.同步电动机采用异步启动法启动时,转子励磁绕组应该___。
A. 接到规定的直流电源
B. 串入一定的电阻后短接
C. 开路
D. 短路
【单选题】
70.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
71.三相刀开关的作用是接通和断开___电路。
A. 大电流
B. 负载
C. 电压或小电流
D. 三相电动机
【单选题】
72.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
73.维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
74.读图的基本步骤有看图样说明,___,看安装接线图。
A. 看主电路
B. 看电路图
C. 看辅助电路
D. 看交流电路
【单选题】
75.电气控制线路图测绘的一般步骤是设备停电,先画电器布置图,再画___,最后画出电气原理图。
A. 电动机位置图
B. 电器接线图
C. 按钮布置图
D. 开关布置图
【单选题】
76.电气控制线路图测绘的方法是___;先画输入端,再画输出端;先画主干线,再画各支路;先简单后复杂。
A. 先画机械,再画电气
B. 先画电气,再画机械
C. 先画控制电路,再画主电路
D. 先画主电路,再画控制电路
【单选题】
77.电气控制线路测绘时要避免大拆大卸,对去掉的线头要___。
A. 保管好
B. 做好记号
C. 用新线接上
D. 安全接地
【单选题】
78.电气控制线路测绘中发现有掉线或接线错误时,应该首先___。
A. 做好记录
B. 把线接_L
C. 断开电源
D. 安全接地
【单选题】
79.电气控制线路测绘前要检验被测设备是否有电,不能___。
A. 切断直流电
B. 切断照明灯电路
C. 关闭电源指示灯
D. 带电作业
【判断题】
1.熔断器类型的选择依据是负载的保护特性、短路电流的大小、使用场合、安装条件和各类熔断器的适用范围。
A. 对
B. 错
【判断题】
2.低压断路器类型的选择依据是使用场合和保护要求。
A. 对
B. 错
【判断题】
3.短路电流很大的场合宜选用直流快速断路器。
A. 对
B. 错
【判断题】
4.交流接触器与直梳接触器的使用场合不同。
A. 对
B. 错
【判断题】
5.交流接触器与直流接触器可以互相替换。
A. 对
B. 错
【判断题】
6.△接法的异步电动机可选用两相结构的热继电器。
A. 对
B. 错
【判断题】
7. Y接法的异步电动机可选用两相结构的热继电器。
A. 对
B. 错
推荐试题
【多选题】
What are two features introduced in Network I/O Control version 3? (Choose two.)___
A. Bandwidth reservation per traffic type
B. Network resource pools
C. CoS tagging
D. Bandwidth guarantee to virtual machines
【多选题】
Which two correct virtual machine advanced configuration parameters will accomplish this? (Choose two.)___
A. isolation.device.edit.disable = “FALSE”
B. isolation.device.edit.disable = “TRUE”
C. isolation.device.connectable.disable = “FALSE”
D. isolation.device.connectable.disable = “TRUE”
【多选题】
Which three statements are correct regarding booting an ESXi Host from Fibre Channel SAN? (Choose three.)___
A. Direct connect topology is supported.
B. Each host must have its own boot LUN.
C. ESXi hosts do not require local storage.
D. Multipathing to a boot LUN on an active-passive array is supported.
E. Hosts can share one common boot LUN.
【多选题】
Which two tasks should a vSphere administrator perform if the vmkernel log reports VMFS metadata errors? (Choose two.)___
A. contact VMware technical support
B. reformat the datastore
C. check the device with VOMA
D. ignore the messages
【多选题】
Which two statements are true for a vCenterServer user account that is used for vSphere Data Protection (VDP)? (Choose two.)___
A. The user account must be assigned with Administrator role.
B. The password for the user account cannot contain spaces.
C. The user account should be created in the Single Sign-On domain
D. The user account cannot inherit required permissions from a group role.
【多选题】
Which three storage protocols are supported by Virtual Volumes? (Choose three.)___
A. FCIP
B. FCoE
C. iSCSI
D. NFS v3
E. NFS v4
【多选题】
A vSphere administrator observes a CPU spike on one of the web servers (view the Exhibit.) Which two statements can describe the cause of this activity? (Choose two.)___
A. The network packet size is too large.
B. VMware Tools is not installed.
C. Disk latency is present on the datastore.
D. The network packet size is too small.
【多选题】
Which three operations can cause VMFS metadata updates? (Choose three.)___
A. Restarting a VM using the guest OS.
B. Launching a VM console.
C. Migrating a VM with vMotion.
D. Powering a VM on or off.
E. Expanding a VMFS datastore.
【多选题】
*What two services run on all nodes in a vCenter Server HA cluster? (Choose two.)___
A. vmware-vmon
B. vmware-vpostgres
C. vmare-rbd-watchdog
D. vmware-vcha
【多选题】
Which two statements are true regarding Auto Deploy in version 6.5? (Choose two.)___
A. Auto Deploy can be configured and managed via PowerCLI.
B. Auto Deploy can be configured and managed via the vSphere Client.
C. Auto
D. eploy can be configured and managed via the vSphere Web Client.
【多选题】
What three options can improve network performance for a virtual machine? (Choose three.)___
A. MLD
B. TSO
C. NetFlow
D. LRO
E. SR-IOV
【多选题】
Which two storage technologies are supported for MSCS? (Choose two.)___
A. NFS
B. VAAI
C. iSCSI
D. FC
【多选题】
When upgrading a VMware vSAN cluster to version 6.5, which two tasks must be completed to comply with upgrade requirements and VMware-recommended best practices? (Choose two.)___
A. Use RVC to upgrade the hosts.
B. Use the latest available ESXi version.
C. Back up all VMs.
D. Use only the “Full data migration” maintenance mode option.
【多选题】
What two enhancements are in VMFS6 but not in VMFS5? (Choose two.)___
A. Support for 4k native disks
B. Support for 512e disks
C. GPT storage device partitioning
D. Automatic space reclamation
【多选题】
Which two statements describe why a vSphere DRS cluster would report load imbalance? (Choose two.)___
A. The configured migration threshold is too high.
B. The configured migration threshold is too low.
C. DRS is configured for Partially Automated.
D. Enhanced vMotion Compatibility (EVC) is enabled.
【多选题】
A vSphere Administrator must ensure that vCenter Server service is running in a domain user account rather than Local System Account. To accomplish this, the user account should have which two permissions? (Choose two.)___
A. Log on as a service.
B. Act as part of the operating system.
C. Log on as a batch job.
D. Log on locally.
【多选题】
A virtual machine fails to power on after being deployed from a template. What two remediation steps could correct this issue? (Choose two.)___
A. Increase CPU reservation
B. Decrease memory reservation
C. Increase memory reservation
D. Increase datastore capacity
E. Decrease CPU reservation
【多选题】
Which three directories are available under the vcsa-cli-installer folder of the vCenter Server Appliance installation media? (Choose three.)___
A. \mac
B. \ovftool
C. \migration-assistant
D. \win32
E. \lin64
【多选题】
What are three considerations when booting ESXihost from SAN software FCoE? (Choose three.)___
A. The VMware_FCoE_vSwitch that the installer automatically created cannot be changed.
B. Boot LUN cannot be shared with other hosts even on shared storage.
C. Multipathing is not supported at pre-boot.
D. Software FCoE boot configuration cannot be changed from within
E. SXi.
【多选题】
Which two choices are applicable to vSphere Availability? (Choose two.)___
A. Heartbeat Datastores
B. VM Startup/Shutdoown
C. Power Management
D. Admission Control
【多选题】
A user is a member of groups A and B. -VM10 and VM20 are in VM Folder. -Group A is assigned permission “Read-only” on VM Folder. What two configurations will allow the user to edit the settings for only VM10? (Choose two.)___
A. Assign group B permission “virtual machine power user” to VM10.
B. Assign group B permission “virtual machine console user” to VM10.
C. Assign group A permission “virtual machine console user” to VM10.
D. Assign group A permission “virtual machine power user” to VM10.
【多选题】
Which two new vSphere 6.5 features enable an Administrator to locate configuration options when creating or editing host profiles more easily than in previous versions? (Choose two.)___
A. Add the configuration option to favorites.
B. Navigate the option tree.
C. Search for the configuration option.
D. Copy the configuration option from a different profile.
【多选题】
What are the two valid storage controller types for VMs on ESXi 6.5? (Choose two.)___
A. FCoE
B. SATA
C. NVMe
D. iSCSI
【多选题】
Which two options can optimize conversion with VMware Converter? (Choose two.)___
A. Disable real-time antivirus scanners.
B. Remove the source from Active Directory.
C. Remove third-party device drivers.
D. Exclude diagnostic partitions from conversion.
E. Disable Volume Shadow Copy (VSS).
【多选题】
vSphere Availability considers which two factors for virtual machine restarts? (Choose two.)___
A. Host Isolation Response
B. file accessibility
C. NUMA node size
D. resource reservations
【多选题】
Which two virtual NICs support Wake-on-Lan to resume a virtual machine that is in standby mode? (Choose two)___
A. Flexible
B. E1000E
C. E1000
D. vmxnet 3
【多选题】
Which two logs should be examined to troubleshoot a Windows vCenter Server upgrade failure? (Choose two.)___
A. vminst.log
B. vim-um-msi.log
C. firstboot.log
D. pkgmgr.log
【多选题】
Which are two supported storage primitives for VAAI NAS? (Choose two.)___
A. Full File Clone
B. Reserve Space
C. hardware assisted locking
D. block zeroing
【多选题】
Which two parameters must be configured for Windows in-guest disk mirroring? (Choose two.)___
A. scsi#.returnNoConnectDuringAPD = “FALSE”
B. scsi#.terminateVMOnPDL = “TRUE”
C. scsi#.returnBusyOnNoConnectStatus = “FALSE”
D. scsi#.returnNoConnectDuringAPD = “TRUE”
【多选题】
Which two items are required to enable NPIV in a virtual machine? (Choose two.)___
A. use of physical RDMs
B. physical HBA support
C. use of virtual disks
D. hardware version 11 or higher
【多选题】
A vSphere Administrator has VM Component Protection (VMCP) enabled, but the VM was not restarted when one of the VMFS datastores experienced an All Paths Down (APD) failure. What two scenarios would explain why the virtual machine was not restarted? (Choose two.)___
A. VM Monitoring is required in order for VMCP to failover during an APD event.
B. VMware Tools is not installed on the guest operating system for the VM.
C. Insufficient Capacity is available on the failover ESXi hosts.
D. The APD failure was corrected before the VM could be restarted.
【多选题】
What are two requirements in order to restore a Resource Pool Tree from a snapshot? (Choose two.)___
A. vSphere DRS must be turned on.
B. A restore can only be performed on a vSphere DRS cluster within the original vCenter Server.
C. vSphere
D. RS must be turned off.
【多选题】
Which three vSphere features are compatible with vSphere Replication? (Choose three.)___
A. vSphere High Availability
B. vSphere Fault Tolerance
C. vSphere Storage
D. RS
【多选题】
What two VMware Remote Console Options can be defined in the virtual machine settings? (Choose two.)___
A. Boot Delay
B. Maximum number of sessions
C. Guest OS lock
D. Total video memory
【多选题】
VMware Converter can import a powered off virtual machine from which two virtual machine platforms?(Choose two.)___
A. Microsoft Hyper-V
B. Citrix Xen
C. VMware Workstation
D. Linux with KVM
【多选题】
Which two options allow storage space reclamation? (Choose two.)___
A. Use VMFS6 datastores.
B. Use esxcli storage vmfs unmap.
C. Use the SAN console (management tool).
D. Use the vSphere Web Client.
【多选题】
An administrator must reprovision 25 hosts with a new image profile that he has created. Which two methods can the administrator use to change the image profile? (Choose two.)___
A. From the vSphere Web client home page, select the Deploy Rules tab in the Auto Deploy section.
B. Run the Copy-Deploy Rule and specify the Replace Item parameter with Power CLI.
C. From the vSphere Web client home page, select the Assign Rules tab in the Auto
D. eploy section.
【多选题】
What are three parameters for traffic filtering or marking? (Choose three.)___
A. Protocol
B. Traffic Direction
C. DSCP value
D. virtual Port ID
【多选题】
The vSphere administrator must change the path selection policy (PSP) to comply with best practices. Which two interfaces can be used to change the PSP? (Choose two.)___
A. ESXi shell
B. vSphere Client
C. ESXi host client
D. vSphere Web Client
【多选题】
In what two ways can Storage DRS load balance virtual machines? (Choose two.)___
A. anti-affinity rules
B. virtual storage controller
C. guest OS family
D. I/O latency