【单选题】
按炸药的组成,可将炸药分成___和混合炸药两大类。
A. 单质炸药
B. 优质炸药
C. 复合炸药
D. 自制炸药
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
电子雷管采用三重密码保护,即爆破员、___各自独立设置密码,三重密码对应起爆。
A. 导通表与起爆器
B. 导通表与雷管
C. 起爆器与雷管
D. 保管员与雷管
【单选题】
电爆网路的导通和电阻值检查,应使用___。
A. 电表
B. 专用爆破电桥
C. 万用表
D. 仪表
【单选题】
起爆电源应指定专人看守,___应由负责人掌握,不到起爆时不准发给起爆人员。
A. 欧姆表
B. 起爆器的转柄
C. 起爆线
D. 大门钥匙
【单选题】
在串联网路中,只要有一发电雷管___断路就会造成整个网路断路。
A. 加强帽
B. 外壳
C. 桥丝
D. 钨丝
【单选题】
多孔粒状铵油炸药的装药密度为0.90g/cm3~0.93g/cm3时,爆速一般为___。
A. 2600m/s
B. 2700m/s
C. 2800m/s
D. 2900m/s
【单选题】
导爆管的管壁材料为高压聚乙烯___。
A. 橡胶
B. 塑料
C. 胶皮
D. 玻璃纤维
【单选题】
根据起爆药包在炮孔中安放的位置不同,有三种不同的起爆方式:___、反向起爆和多点起爆。
A. 电起爆
B. 正向起爆
C. 非电起爆
D. 平行起爆
【单选题】
自由面越多,爆破破碎越容易,爆破效果也___。
A. 越差
B. 越坏
C. 越容易
D. 越好
【单选题】
煤矿井下光面爆破时,周边光爆炮眼应用炮泥封实,且封泥长度不得小于___。
A. 0.6m
B. 0.5m
C. 0.4m
D. 0.3m
【单选题】
深孔爆破时,炮孔布置形式一般有___、正方形和矩形三种。
A. 三角形
B. 波浪形
C. 圆型
D. 椭圆形
【单选题】
裸露药包爆破时要注意大块石的形状,尽量将药包放置在___部位。
A. 平行
B. 突出
C. 凸形
D. 凹形
【单选题】
以下描述中哪个是描述拒爆的?___
A. 雷管和炸药都没有爆炸
B. 雷管引爆了炸药
C. 炸药在传爆过程中熄灭了,孔底留有残药
D. 炸药在地下爆出了一个大坑
【单选题】
多头掘进时,爆破母线要随用随挂。爆破母线必须挂在电缆、信号线下方,距离要大于___。
A. 0.3m
B. 0.4m
C. 0.5m
D. 0.6m
【单选题】
在炮孔内放置起爆药包时,雷管脚线要顺直,轻轻拉紧并贴在孔壁一侧,防止损坏___,同时可减少炮棍捣坏脚线的机率。
A. 炮孔
B. 雷管
C. 药包
D. 脚线
【单选题】
煤矿井下爆破工作面有2个或2个以上自由面时,在煤层中最小抵抗线不得小于___。
A. 0.6m
B. 0.5m
C. 0.4m
D. 0.3m
【单选题】
对于一般民用建筑物,当主振频率在10Hz<f≤50Hz范围时,其爆破振动安全允许标准为___cm/s。
A. 1~1.5
B. 1.5~2
C. 2.0~2.5
D. 2.5~3
【单选题】
一般情况下,矿山的井下爆破器材库是建在___用于储存民用爆炸物品的硐室。
A. 地下
B. 地面
C. 地上
【单选题】
井下库区的照明电压应不超过___V;
A. 12
B. 36
C. 127
【单选题】
在爆破作业现场,应当由爆破员与安全员___清点剩余的爆破器材,共同签字确认使用和剩余爆破器材的记录。
A. 先后
B. 独立
C. 共同
【单选题】
水溶解池场地和残渣烧毁场地都要选择在野外,___、交通方便、不污染水源的地方。
A. 生活方便
B. 燃料充足
C. 水源丰富
【单选题】
爆炸销毁场地应距10万人口以下城市的边缘保持在___km以上。
A. 2
B. 5
C. 10
【单选题】
储存库内爆破器材堆垛与堆垛之间应留有宽度不小于___m的装运通道。
A. 1
B. 1.2
C. 1.5
【单选题】
采用爆炸法销毁导爆索时,一次销毁导爆索的长度不宜超过___m,而且要与其它爆炸物品分开销毁。
A. 500
B. 800
C. 1000
【单选题】
根据《小型民用爆炸物品储存库安全规范》(GA838)的有关规定,民爆库房单库储存雷管的数量不能大于___发。
A. 10000
B. 20000
C. 30000
【单选题】
用溶解法销毁黑火药时,___丢入河塘江湖及下水道中。
A. 可以
B. 不应直接
C. 在安全的情况下,可以
【单选题】
爆破员、安全员、保管员的年龄应在18周岁以上,___周岁以下。
A. 55
B. 58
C. 60
【单选题】
爆破员岗位职责要求,爆破员应___好自己所领取的民用爆炸物品。
A. 保管
B. 使用
C. 储存
【单选题】
爆破作业结束后应当及时检查、___未引爆的民用爆炸物品。
A. 生产
B. 运输
C. 排除
【单选题】
4、民用爆炸物品的装载应符合国家有关标准和规范,车厢内不得___。
A. 载人
B. 装载炸药
C. 装载雷管
【单选题】
手持机系统由手持机、lC卡和___组成。
A. 条码
B. U盘
C. 密码
【单选题】
爆破作业单位聘用无资格人员从事爆破作业或爆破器材管理的,可由公安机关对单位处___的罚款。
A. 10万元以上
B. 10万元以上50万元以下
C. 50万元以下
【单选题】
___的销售、购买及废旧民用爆炸物品销毁等行为,都适用《民用爆炸物品安全管理条例》。
A. 硝酸铵
B. 剧毒物品
C. 复合肥
【单选题】
经由道路运输民用爆炸物品的,要严格执行《民用爆炸物品运输许可证》“___”的规定。
A. 一车一证一次使用
B. 一证一车多次使用
C. 一证一车一次使用
【单选题】
爆破作业单位聘用无资格人员从事爆破作业或爆破器材管理的,可由公安机关对行为人予以___。
A. 行政拘留
B. 罚款
C. 批评教育
【单选题】
冲击波感度是指在___作用下炸药发生爆炸的难易程度。
A. 超声波
B. 冲击波
C. 地震波
D. 电磁波
【单选题】
多孔粒状铵油炸药的装药密度为0.90g/cm3~0.93g/cm3时,爆速一般为___。
A. 2600m/s
B. 2700m/s
C. 2800m/s
D. 2900m/s
【单选题】
目前,常用的工业雷管主要有___、导爆管雷管和电子雷管三大类。
A. 电雷管
B. 毫秒电雷管
C. 半秒雷管
D. 秒雷管
【单选题】
乳化炸药分___、煤矿乳化炸药和露天乳化炸药三种类型,它是目前使用最广泛的含水炸药。
A. 岩石乳化炸药
B. 液体乳化炸药
C. 固体乳化炸药
D. 铵油乳化炸药
【单选题】
抗静电电雷管按延期时间分为抗静电___电雷管和抗静电毫秒延期电雷管。
A. 半秒
B. 瞬发
C. 秒
D. 毫秒
【单选题】
起爆电子雷管需要专门的起爆设备并需要通过___识别,如密码正确则启动内置的延期程序,达到规定的延期时间后,才输出强的电流信号引爆雷管。
A. 数字
B. 密码
C. 程序
D. 地址
推荐试题
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。
A. 四相
B. 三相
C. 两项
D. 单相