【单选题】
(33021)柴油机的一种故障，可能表现出几种异常现象，如，柴油机供油系统中喷油泵柱塞磨损，下列一组可能的故障现象全对的是( )。(1.0分)___
A. 启动困难、功率不足、低速运转不稳定、冒白烟
B. 启动困难、功率不足、低速运转不稳定、冒黑烟
C. 启动困难、功率不足、低速运转不稳定、冒蓝烟
D. 启动困难、超速、低速运转不稳定、冒黑烟
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
(33022)柴油机启动困难，下列可能出现的故障全对的一组是( )。(1.0分)___
A. 电池电压不足、燃油供给不足、外温过高、进气不畅、燃油中含有水分
B. 电池电压不足、燃油供给不足、冷却水温过高、进气不畅、燃油中含有水分
C. 电池电压不足、燃油供给不足、烧机油、进气不畅、燃油中含有水分
D. 电池电压不足、燃油供给不足、气门漏气、进气不畅、燃油中含有水分
【单选题】
(33023)对于柴油机的故障，下列说法正确的是( )。(1.0分)___
A. 柴油机产生故障，看不见、听不到、摸不着
B. 柴油机的故障，一般是孤立的
C. 柴油机的故障，一般是相互联系的
D. 柴油机的故障，必须通过仪器检测
【单选题】
(33025)冬季柴油机不易启动，( )不是其中原因之一。(1.0分)___
A. 机油黏度大，不易流动
B. 上油箱油位低于3/4
C. 柴油黏度大，不易流动
D. 气缸散热快，使使压缩冲程终了时的温度低，柴油不易燃烧
【单选题】
(33026)发电车柴油机组正常运行时，如果出现游车，下列( )不是其中原因之一。(1.0分)___
A. 上油箱缺油
B. 燃油系统中有空气
C. 执行器故障
D. 控制系统电压低于19V
【单选题】
(33027)发电车柴油机出现游车，下列处理方法不正确的是( )。(1.0分)___
A. 如果因为燃油精滤器脏堵，更换燃油精滤器，同时清洗燃油粗滤器
B. 如果是因为执行器脏堵，则更换燃油精滤器
C. 如果是燃油中有空气，则排气
D. 如果是个别喷油器不工作，则调整柱塞行程或更换喷油器
【单选题】
(33030)发电车运行中，如果柴油机主循环水管道爆裂，大量冷却水外泄，正确的应急处理方法是( )。(1.0分)___
A. 积极处理水管爆裂处
B. 尽力处理爆裂处，一旦处理不好时，再停机，启用别的机组供电
C. 关闭膨胀水箱与该机的水阀，停机，启用别的机组供电
D. 要求停车补水
【单选题】
(33031)发电车康明斯柴油机运行中，如果燃油精滤器至PT泵的油管漏油，正确的应急处理方法( )。(1.0分)___
A. 积极处理漏油处
B. 停机、关油阀，立即更换其他机组供电
C. 关油阀，再处理，如果处理不好，就停机
D. 用包扎带捆绑，只好减少渗漏就行了
【单选题】
(33032)发电车运行途中，如果冷却单节大量漏水，正确的处理程序是( )。(1.0分)___
A. 关闭该机水管与膨胀水箱的阀门→停机→启用其他机组供电→积极处理漏水处
B. 关闭该机水管与膨胀水箱的阀门→积极处理漏水处→停机→启用其他机组供电
C. 停机→关闭该机水管与膨胀水箱的阀门→积极处理漏水处→启用其他机组供电
D. 停机→关闭该机水管与膨胀水箱的阀门→启用其他机组供电→积极处理漏水处
【单选题】
(33035)发电车运行中，柴油机进排气管道漏气，正确的处理方法是( )。(1.0分)___
A. 更换其他机组供电，同时积极处理漏气处
B. 无需停机，用铁丝、包扎布绑紧漏气管道
C. 将备用机组的管道拆下，替换漏气管
D. 更换其他机组供电，填写“车统-181”交库检处理
【单选题】
(33036)柴油机出现“飞车”，下列不正确的处理方法是( )。(1.0分)___
A. 关掉进油阀，切断燃油进油管
B. 迅速堵住空气滤清器进气口，切断进气
C. 关掉配电屏上的停机开关
D. 有减压装置的柴油机，将减压手柄推到减压位，打开气门，使缸内空气减压
【单选题】
(33037)发电车运行途中柴油机突然停机，下列检查方法不正确的是( )。(1.0分)___
A. 检查24V电源系统
B. 检查柴油机操纵盘的报警指示灯
C. 检查上油箱油量
D. 检查冷却塔
【单选题】
(33038)发电车运行中康明斯柴油机突然停机，不可能是下列原因之一的是( )。(1.0分)___
A. 缺燃油
B. 停车电磁阀不得电
C. 24V电源保险断路
D. 柴油机过载
【单选题】
(33039)发电车康明斯柴油机运行中突然停机，正确的处理方法是( )。(1.0分)___
A. 检查24V电源，如正常，立即启动其他机组供电，再积极处理突然停机故障
B. 处理突然停机故障，应先检查燃油滤清器
C. 处理突然停机故障，应先检查空气滤清器
D. 当确认故障已排除，无需排空气，即可启机试验
【单选题】
(33040)发电车康明斯柴油机油底壳进柴油的原因，下列说法正确的是( )。(1.0分)___
A. 停机时未关闭进油阀或油阀不良，而喷油器正处于供油位，因油位压差较大，使得柴油渗入缸内流到油底壳
B. 停机时未关闭进油阀或油阀不良，因上油箱油位过高，压差大，把柴油通过喷油器压进油底壳
C. 柴油机工作时，喷油器雾化不良，滴入的柴油经燃烧室流入到油底壳
D. 柴油机工作时，由于进气量不足，柴油没有充分燃烧，多余的柴油经燃烧室流入到油底壳
【单选题】
(33041)发电车康明斯柴油机油底壳进柴油，下列处理方法正确的是( )。(1.0分)___
A. 分解清洗或更换电磁阀及进油阀、更换机油、更换机油滤清器
B. 更换所有喷油器、更换机油、更换机油滤清器
C. 更换机油、更换燃油滤清器、清洗燃油粗滤器
D. 更换机油、更换机油滤清器、清洗PT泵
【单选题】
(33042)发电车康明斯柴油机油底壳进柴油，会引起一些故障现象，下列说法正确的是( )。(1.0分)___
A. 油底壳机油面升高，机油压力升高，润滑不良，机油温度升高，冷却水温升高
B. 油底壳机油面升高，机油压力降低，润滑不良，机油温度降低，冷却水温降低
C. 油底壳机油面升高，机油压力降低，润滑不良，机油温度降低，冷却水温升高
D. 油底壳机油面升高，机油压力降低，润滑不良，机油温度升高，冷却水温升高
【单选题】
(33043)发电车康明斯柴油机油底壳进水，下列可能出现的故障原因不正确的是( )。(1.0分)___
A. 机油冷却器破裂
B. 缸套裂纹或穴蚀穿孔
C. 缸盖垫冲坏或缸套密封胶圈损坏
D. 中间冷却器破裂
【单选题】
(33044)发电车柴油机与发电机安装后，如果同轴度有偏差，产生下列故障现象不正确的是( )。(1.0分)___
A. 有异常振动
B. 有异响
C. 发电机发电偏低
D. 轴承有异常温升
【单选题】
(33045)发电车柴油机与发电机联结时，正确的操作方式是( )。(1.0分)___
A. 将柴油机水平地放在机架上→纵向保持柴油机与机架对齐→紧固柴油机四角→吊入发电机→给发电机加或减钢垫→水平升高或降低发电机直到轴心与柴油机轴心处在同一直线上→紧固发电机四角螺栓→对角紧固联结螺栓，均匀使发电机圆周靠向柴油机并紧固
B. 将柴油机水平地放在机架上→纵向保持柴油机与机架对齐→紧固柴油机四角→吊入发电机→给发电机加或减钢垫→水平升高或降低发电机直到轴心与柴油机轴心处在同一直线上→对角紧固联结螺栓，均匀使发电机圆周靠向柴油机并紧固→紧固发电机四角螺栓
C. 将柴油机水平地放在机架上→纵向保持柴油机与机架对齐→吊入发电机→紧固柴油机四角→给发电机加或减钢垫→水平升高或降低发电机直到轴心与柴油机轴心处在同一直线上→对角紧固联结螺栓，均匀使发电机圆周靠向柴油机并紧固→紧固发电机四角螺栓
D. 将柴油机水平地放在机架上→紧固柴油机四角→纵向保持柴油机与机架对齐→吊入发电机→给发电机加或减钢垫→水平升高或降低发电机直到轴心与柴油机轴心处在同一直线上→对角紧固联结螺栓，均匀使发电机圆周靠向柴油机并紧固→紧固发电机四角螺栓
【单选题】
(33046)发电车柴油机与发电机同轴度偏差较大，不会引起下列( )后果。(1.0分)___
A. 柴油机无用功加大
B. 电机轴承损坏
C. 发电机扫膛
D. 柴油机烧机油
【单选题】
(33047)冬季发电车运行时，下油箱燃油析蜡，下列处理方法全正确的一组是( )。(1.0分)___
A. 采用“手动位”启动交流燃油泵连续抽油、启动车上所有柴油机、减少柴油机负载、停站时向下油箱内注热水
B. 采用“手动位”启动交流燃油泵连续抽油、启动车上所有柴油机、在下油箱加防冻液、停站时向下油箱外浇热水
C. 采用“手动位”启动交流燃油泵连续抽油、启动车上所有柴油机、减少柴油机负载、向下油箱加盐
D. 采用“手动位”启动交流燃油泵连续抽油、启动车上所有柴油机、减少柴油机负载、停站时向下油箱外浇热水
【单选题】
(33048)冬季发电车运行时，下油箱析蜡，会引起下列( )后果。(1.0分)___
A. 柴油机燃烧不充分，功率下降
B. 柴油中混有蜡杂物，柴油机会游车
C. 柴油中混有蜡杂物，柴油机会出现“飞车”
D. 下油箱的油因凝结成蜡状，燃油抽不到上油箱，柴油机因缺油而停机
【单选题】
(33054)康明斯发电车冷却风机手动位时，若出现水温超过88℃，风机仍未自动启动，这一故障最大可能性是( )。(1.0分)___
A. 风机手动启动按钮损坏
B. 85℃水温开关无法闭合
C. 65℃水温开关无法断开
D. KA8线圈无法自锁
【单选题】
(33058)发电车燃油供给管路出现堵塞，一般的查找方法是( )。(1.0分)___
A. 先断开油源接口检查
B. 先断开油管路中间接口检查
C. 先断开油管路末端接口检查
D. 先断开油管路任意位置检查
【单选题】
(33059)发电车运行中，出现下油箱至上油箱管路堵塞，应急处理方法正确的是( )。(1.0分)___
A. 将随车应急软管一头插入下油箱，触底并固定，另一头接在交流燃油泵进油管接头处，用喉箍锁紧，即可抽油
B. 将随车应急软管一头插入下油箱，触底并固定，另一头接在交流燃油泵出油管接头处，用喉箍锁紧，即可抽油
C. 将随车应急软管一头插入下油箱，距箱底部约100mm处并固定，另一头接在交流燃油泵进油管接头处，用喉箍锁紧，即可抽油
D. 将随车应急软管一头插入下油箱，距箱底部约100mm处并固定，另一头接在手摇泵进油管接头处，用喉箍锁紧，即可抽油
【单选题】
(33060)发电车燃油泵在“手动位”不能正常抽油，下列原因正确的是( )。(1.0分)___
A. 燃油管路堵塞
B. 油泵后面的油管进空气
C. 上油箱油已抽满
D. 燃油内含有水分
【单选题】
(33061)发电车燃油泵不工作，属电路故障原因正确的是( )。(1.0分)___
A. 分闸按钮常开
B. 合闸按钮常闭
C. “应急/正常”转换开关处在“应急位”
D. 油满限位开关常开
推荐试题
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
A. 24
B. 48
C. 64
D. 128
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
