【填空题】
23075.___RS232C 接口传输数据最多可实现一台计算机对三台机床。
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
(错
解析
暂无解析
相关试题
【填空题】
23076.___接入局域网的数控机床必须有网络适配器。
【填空题】
23077.___平面铣削时,正反进给方向各铣一段,只要发现一个方向进给时有拖刀现象,则说明铣床主轴轴线与机床台面不垂直。
【填空题】
23078.___零件加工用立铣刀侧刃铣削凸模平面外轮廓时,应沿外轮廓曲线延长线的切线方向逐渐切离工件。
【填空题】
23079.___有一个轴为常量的二次曲面铣加工,刀具半径补偿可以用 G41 或 G42 实现。
【填空题】
23080.___铰刀按用途分为机用铰刀和手用铰刀。
【填空题】
23081.___在一个等直径的圆柱形轴上铣一条两端封闭键槽,需限制工件的五个自由度。
【填空题】
23082.___一个工艺尺寸链中有且只有一个组成环。
【填空题】
23083.___若回转轴前工序加工径向尺寸为 d1,本工序加工径向尺寸到 d2,则其在直径上的工序余量为 d1-d2。
【填空题】
23084.___当实际生产中不宜选择设计基准作为定位基准时,则应选择因基准不重合而引起的误差最小的表面作定位基准。
【填空题】
23085.___千分表的传动机构中传动的级数要比百分表多,因而放大比更大,测量精度也更
【填空题】
23086.___测量复杂轮廓形状零件可选用万能工具显微镜。
【填空题】
23087.___孔的圆柱度误差是沿孔轴线方向取不同位置测得的最大差值即为孔的圆柱度误差。
【填空题】
23088.___表面粗糙度高度参数 Ra 值愈大,表示表面粗糙度要求愈高;Ra 值愈小,表示表
【填空题】
23089.___机床的日常维护与保养,通常情况下应由后勤管理人员来进行。
【填空题】
23090.___导轨面直线度超差会使进给机构噪声加大。
【填空题】
23091.___职业道德的主要内容包括:爱岗敬业、诚实守信、办事公道、服务群众、奉献社
【填空题】
23092.___带的失效形式主要是打滑与疲劳破坏。
【填空题】
23093.___链传动只能用于平行轴间的传动。
【填空题】
23094.___影响蜗轮副啮合精度的因素以蜗杆轴线偏移蜗轮轮齿对称中心面为最大。
【填空题】
23095.___数控铣床在进给系统中采用步进电机,步进电机按电脉冲数量转动相应角度。
【填空题】
23096.___显示器的主要原理是以电流刺激液晶分子产生点、线、面配合背部灯管构成画面。
【填空题】
23097.___消除一般的病毒,拔掉网线后,用杀毒软件杀毒,然后再把相关的系统补丁补上。
【填空题】
23098.___平行线法的展开条件应满足且在投影面上反映实长。
【填空题】
23099.___选择精基准时,先用加工表面的设计基准为定位基准,称为基准重合原则。
【填空题】
23100.___改善零件、部件的结构工艺性,可便于加工和装配,从而提高劳动生产率。
【填空题】
23101.___销在机械中除起到连接作用外还可起定位作用和保险作用。
【填空题】
23102.___市场经济时刀具企业只负责生产专用刀具,标准刀具、非标准刀具都由用户行业
【填空题】
23103.___由于零件的相互运动,使摩擦表面的物质不断损失的现象叫磨损。磨损过程中, 单位时间内材料的磨损量不变。
【填空题】
23104.___在数值计算过程中,已按绝对坐标值计算出某运动段的起点坐标及终点坐标,以增量尺寸方式表示时,其换算公式:增量坐标值=终点坐标值-起点坐标。
【填空题】
23105.___GSK990M 数控系统孔加工数据:G73 方式中,P 规定孔底暂停时间,单位为 s。
【填空题】
23106.___CAXA 制造工程师软件中“网格面”要求所有的 U 向和 V 向曲线都必须有交点。
【填空题】
23107.___CAXA 制造工程师可以直接生成 G 代码,不需要生成刀位文件再作处理。
【填空题】
23108.___GSK983 系统编辑程序时,按地址键和数字键即可直接插入。
【填空题】
23109.___数控机床既可以自动加工,也可以手动加工。
【填空题】
23110.___数控加工中,程序调试的目的:一是检查所编程序是否正确,再就是把编程零点, 加工零点和机床零点相统一。
【填空题】
23111.___标准麻花钻主切削刃上各点处的后角大小不相等,外缘处最小,约为 1~4 度。
【填空题】
23112.___汽轮机高中压外缸结构要素复杂,模型的建立困难。某高中压外缸模型的特征量多达 600 多个,而特征建立的顺序直接影响着后面 NC 加工的进行。
【填空题】
23113.___4 轴联动或 5 轴联动加工与 5 个以上轴的同时加工,称为多轴加工。
【填空题】
23114.___加工整体叶轮,需要注意的主要问题是避免干涉,曲面的自身干涉和曲面间的面间干涉。
【填空题】
23115.___铣床床台上的T形槽,其用途之一为当基准面。
推荐试题
【多选题】
A vSphere Administrator observes that the Primary VM configured with Fault Tolerance is executing slowly. After further investigation, it is determined that the Secondary VM is on an overcommitted ESXi host. What two methods will correct the problem? (Choose two.)___
A. Use Storage vMotion to migrate the Secondary VM to another datastore.
B. Use vMotion to migrate the Secondary VM to a different ESXi host.
C. Configure a CPU limit on the Primary VM which will also apply to the Secondary VM.
D. Turn off and turn on FT in order to recreate the Secondary VM on a different datastore.
【多选题】
Which two features require the use of Host Profiles? (Choose two.)___
A. Host Customizations
B. shared storage
C. Auto
D. eploy
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
Which two statements correctly describe VM-Host affinity rules? (Choose two.) ___
A. When there is more than one VM-Host affinity rule in a vSphere DRS cluster, the rules are applied equally.
B. After creating a VM-Host affinity rule, its ability to function in relation to other rules is predetermined.
C. When there is more than one VM-Host affinity rule in a vSphere
D. RS cluster, the rules will be ranked.
【多选题】
An administrator wants to enable proactive HA by moving virtual machines automatically if a hardware alert is triggered. What are the three required settings? (Choose three.)___
A. Set vSphere DRS Automation to Partially Automated.
B. Turn on Proactive HA.
C. Set the Proactive HA Automation Level to Manual.
D. Set the Proactive HA Automation Level to Automated.
E. Turn on vSphere HA and vSphere DRS.
【多选题】
If vCenter Server 5.5 installation has one or more services deployed remotely, which three services are relocated to vCenter Server 6.5 on upgrade? (Choose three.)___
A. vCenter Inventory Services
B. vSphere Authentication Proxy
C. vSphere Web Client
D. vSphere
E. SXi Dump Collector
【多选题】
What two debugging levels can a virtual machine be configured to? (Choose two.)___
A. Verbose
B. Debugging
C. Statistics
D. Trivia
【多选题】
What are three benefits of using a few large-capacity LUNs instead of many small-capacity LUNs? (Choose three.) ___
A. Better performance because there is less contention for a single volume.
B. More flexibility for resizing virtual disks.
C. Less wasted storage space.
D. More flexibility to create virtual machines without adding new LUNs.
E. Fewer VMFS datastores to manage.
【多选题】
Which two configurable options are available in Boot Options for a virtual machine? (Choose two.)___
A. Tools Upgrades
B. Encryption
C. Firmware
D. Force BIOS setup
【多选题】
Which three VMware-recommended best practices should an administrator follow before upgrading to vSphere 6.5? (Choose three.)___
A. Disconnect ESXi host from vCenter.
B. VMware Tools are installed in the virtual machine.
C. Ensure that the system hardware complies with ESXi requirements.
D. Back up the host.
E. Check the interoperability of any other software integrated with vSphere.
【多选题】
What are two requirements to enable EVC in vSphere DRS cluster? (Choose two.)___
A. CPUs must be from the same vendor.
B. EVC must use the lowest possible baseline supported by the hardware.
C. CPUs must be in the same family and of the same speed.
D. No VMs may be running in the cluster.
【多选题】
What three conditions could result in VMware Flash Read Cache being unable to claim a disk? (Choose three.)___
A. The disk is not listed in the VMware hardware compatibility guide.
B. The disk is not detected as an SSD.
C. The disk is not detected as local.
D. The disk is in use by VMFs.
【多选题】
Boot from SAN is supported on which three storage technologies? (Choose three.)___
A. VMware vSAN
B. FCoE
C. NFS 4.1
D. iSCSI
E. FC
【多选题】
Which two components are part of storage I/O multipathing on ESXi? (Choose two.)___
A. SATP
B. VASA
C. PSP
D. VAAI
【多选题】
Which two statements are true about Highly Available vSphere Auto Deploy infrastructure? (Choose two.)___
A. It helps prevent data loss.
B. It is a prerequisite for using vSphere Auto Deploy with stateful install.
C. It requires two or more Auto
D. eploy servers.
【多选题】
The virtual machine log rotation size can be changed for all VMs by which two interfaces? (Choose two.)___
A. PowerCLI
B. vSphere Web Client
C. ESXi host client
D. esxcli
【多选题】
Which two configuration options can exclude virtual disks from snapshot operations? (Choose two.)___
A. Use RDM in virtual mode for virtual disk.
B. Use virtual disks in Independent – Persistent mode.
C. Use a virtual disk larger than 2 TB in size.
D. Use RDM in physical mode for virtual disk.
【多选题】
Which two storage configurations on the source server are unsupported with VMware Converter? (Choose two.)___
A. Linux LVM
B. software RAID
C. GPT/MBR hybrid disks
D. Windows basic volumes
E. Windows dynamic volumes
【多选题】
Which two statements about vCenter HA are correct? (Choose two.)___
A. ESXi 5.5 or later is required.
B. vCenter HA network latency between nodes must be less than 50 ms.
C. NFS datastore is supported.
D. It must be deployed on a 3
E. SXi host cluster with DRS enabled.
【多选题】
An attempt to delete NFS datastore from a ESXi host returns the error: Sysinfo error on operation returned the following status:< Busy> Which two statements could explain this failure? (Choose two.)___
A. NFS datastore is a part of Storage DRS Cluster.
B. NFS.VolumeRemountFrequency value is set to 30.
C. Storage I/O Control is enabled on NFS datastore.
D. NFS datastore has running or registered virtual machines.
【多选题】
An administrator finds that the Microsoft Exchange virtual machines are exhibiting network latency. What two in-guest changes can help decrease latency? (Choose two.)___
A. LRO
B. TSO
C. SR-IOV
D. PVRDMA
【多选题】
Which two types of iSCSI adapters require VMkernel networking configuration? (Choose two.)___
A. dependent hardware
B. in-guest
C. software
D. independent hardware
【多选题】
Which two statements are true for NFS v4.1 firewall behavior? (Choose two.)___
A. It closes port 2049.
B. It sets allowed. All flag to TRUE.
C. It sets allowed. All flag to FALSE.
D. It opens port 2049.
【多选题】
A vSphere Administrator attempts to enable Fault Tolerance for a virtual machine but receives the following error: Secondary VM could not be powered on as there are no compatible hosts that can accommodate it. What two options could cause this error? (Choose two.)___
A. The other ESXi host(s) are in Maintenance Mode.
B. Hardware virtualization is not enabled on the other ESXi host(s).
C. The other ESXi host(s) are in Quarantine Mode.
D. Hardware MMU is enabled on the other
E. SXi host(s).
【多选题】
Storage capabilities be populated in what two ways? (Choose two.)___
A. The administrator can use tags to describe capabilities.
B. Default capabilities are provided by vCenter Server.
C. Datastores can advertise their capabilities through VAAI.
D. Datastores can advertise their capabilities through VASA.
【多选题】
In network troubleshooting it is important to know what upstream switch the ESXi host is connected to. Which two features does ESXi provide to help identify the upstream switch? (Choose two.)___
A. Promiscuous mode
B. DPM
C. LLDP
D. CDP
【多选题】
Virtual Volumes supports which three VMware features? (Choose three.)___
A. Instant Clones
B. Distributed Resource Scheduler
C. Linked Clones
D. vMotion
E. Storage Distributed Resource Scheduler
【多选题】
vSphere DRS helps to balance virtual machines with available resources in a vSphere cluster. What three types of resources can be taken into account for balancing? (Choose three.)___
A. CPU
B. physical NIC saturation of an ESXi host
C. virtual NIC saturation of a virtual machine
D. RAM
E. storage latency
【多选题】
Which three design requirements must be satisfied to enable RAID-6 objects in a VMware vSAN cluster? (Choose three.)___
A. vSAN Advanced license or higher
B. vSAN stretched cluster
C. at least six hosts contributing storage
D. deduplication and compression
E. all flash configuration
【多选题】
When using "Cluster resource percentage" for host failover capacity in vSphere HA Admission Control, the total resource requirements are calculated from which two values? (Choose two.)___
A. Total vCPUs assigned to each VM.
B. Average CPU usage on each VM over time.
C. Memory reservations on each VM.
D. Total memory assigned to each VM.
E. Average active memory on each VM over time.
F. CPU reservations on each VM.
【多选题】
Which are four attributes of the Active vCenter HA node? (Choose four)___
A. It uses the vCenter HA network to communicate with the Witness node.
B. It constantly replicates vPostgres data with the Witness node.
C. It uses a public IP address for the management interface.
D. It runs the active vCenter Server Appliance instance.
E. It uses the vCenter HA network for replication of data to the Passive node.
F. It provides a quorum to protect against split-brain situations.
【多选题】
Which are two vCenter Server two-factor authentication methods? (Choose two.)___
A. RSA SecurID
B. Smart Card
C. SAML
D. Symantec VIP
【多选题】
An administrator is creating VMkernel adapters on an ESXi 6.5 host and wants to create separate VMkernel adapters for every type of traffic in the default TCP/IP stack. Which three types of traffic can be explicitly enabled on a separate VMkernel adapter? (Choose three.)___
A. Virtual SAN traffic
B. NFS traffic
C. vMotion traffic
D. vSphere HA traffic
E. Fault Tolerance logging traffic
【多选题】
When migrating a Windows vCenter Server 6.0 to the vCenter Server Appliance 6.5, which two will be migrated by default? (Choose two.)___
A. Local Windows OS users and groups
B. Configuration
C. Custom ports
D. FQDN
E. Historical and Performance data
【多选题】
Which three types of Content Libraries exist within vSphere 6.5? (Choose three.)___
A. Remote Content Library
B. Published Content Library
C. Local Content Library
D. Shared Content Library
E. Subscribed Content Library
【多选题】
An administrator cannot enable multi-processor Fault Tolerance (SMP-FT) for a virtual machine. Which are two possible causes for this? (Choose two.)___
A. The virtual machine is running on a vSAN datastore.
B. The Fault Tolerance network is using a 10Gbit uplink.
C. The virtual machine has 6 vCPUs assigned.
D. The virtual machine has a 1TB VMDK attached.
E. The virtual machine has snapshots present.
【多选题】
Which two statements are true for Predictive DRS? (Choose two.)___
A. It balances resource utilization for virtual machines with unpredictable utilization patterns.
B. It integrates DRS with vRealize Operations Manager to balance workloads for virtual machines before resource utilization spikes occur.
C. It balances resource utilization based on a threshold's algorithm that runs each night.
D. It determines the best placement and balance of virtual machines based on a threshold's algorithm that runs each night in vCenter Server 6.5 Database.
【多选题】
Which two situations could cause a virtual machine to appear with (orphaned) appended to its name? (Choose two.)___
A. if a host failover is unsuccessful
B. if a virtual machine was removed from vCenter Server's inventory
C. if a virtual machine was deployed from template, and the template has been deleted
D. if a virtual machine is unregistered directly on the host
【多选题】
Which three requirements are needed to apply RAID 5 or RAID 6 erasure coding on a vSAN 6.2 or 6.5 object? (Choose three.)___
A. on Disk Format 3.0
B. Hybrid vSAN
C. All Flash vSAN
D. vSAN Advanced License
E. Stretched Cluster Configurations