【单选题】
What is the default pathing policy for most active-active arrays?___
A. Fixed
B. Most Recently Used
C. Dynamic
D. isk Morroring
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
Which command will show the iSCSI sessions on a ESXi 6.5 host?___
A. esxcli storage iscsi session get
B. esxcli iscsi session get
C. esxcli storage iscsi session
D. esxcli iscsi session list
【单选题】
Which of the following is not a parameter for traffic filtering or marking?___
A. virtual port ID
B. Protocol
C. Traffic Direction
D. DSCP value
E. Traffic redirection
【单选题】
A vSphere administrator wants to enable a virtual machine with Secure Boot, but in VM setting, Secure Boot option was not found under Boot Options. What could be the cause?___
A. The virtual hardware is not compatible.
B. The virtual machine has missing drivers.
C. The virtual machine OS does not support secure boot.
D. VMware Tools is not upgraded.
【单选题】
A virtual machine is connected on a distributed port group where the average bandwidth configured in the traffic shaping policy is 100 Mbps. The VM network adapter is configured with a reservation of 200 Mbps. What is the VM’s effective bandwidth?___
A. 200 Mbps
B. 100 Mbps
C. 150 Mbps
D. 400 Mbps
【多选题】
What are two reasons why a datastore in a Storage DRS cluster cannot enter maintenance mode?(Choose two.)___
A. Storage latency is too high to allow Storage DRS initiate Storage vMotion.
B. Storage DRS is configured for a VMFS3 datastore.
C. Storage
D. RS is disabled on the virtual disk.
【多选题】
What two methods are used to configure VMware vSphere Storage I/O Control shares and limits? (Choose two.)___
A. Assign shares and limits to VM virtual disks.
B. Assign shares and limits to datastores.
C. Assign shares and limits to Storage (DRS) clusters.
D. Assign shares and limits using VM storage policies.
【多选题】
ESXi 6.5 introduces VMFS6, which supports both 512e and 512n devices. What three configurations are supported when using these devices? (Choose three.) ___
A. Hosts with both 512e and 512n devices.
B. Storage vMotion between both 512e and 512n devices.
C. Datastore Extents spanned between both 512e and 512n devices.
D. Storage DRS clusters containing only both 512e and 512n devices.
【多选题】
A vSphere Administrator observes that the Primary VM configured with Fault Tolerance is executing slowly. After further investigation, it is determined that the Secondary VM is on an overcommitted ESXi host. What two methods will correct the problem? (Choose two.)___
A. Use Storage vMotion to migrate the Secondary VM to another datastore.
B. Use vMotion to migrate the Secondary VM to a different ESXi host.
C. Configure a CPU limit on the Primary VM which will also apply to the Secondary VM.
D. Turn off and turn on FT in order to recreate the Secondary VM on a different datastore.
【多选题】
Which two features require the use of Host Profiles? (Choose two.)___
A. Host Customizations
B. shared storage
C. Auto
D. eploy
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
Which two statements correctly describe VM-Host affinity rules? (Choose two.) ___
A. When there is more than one VM-Host affinity rule in a vSphere DRS cluster, the rules are applied equally.
B. After creating a VM-Host affinity rule, its ability to function in relation to other rules is predetermined.
C. When there is more than one VM-Host affinity rule in a vSphere
D. RS cluster, the rules will be ranked.
【多选题】
An administrator wants to enable proactive HA by moving virtual machines automatically if a hardware alert is triggered. What are the three required settings? (Choose three.)___
A. Set vSphere DRS Automation to Partially Automated.
B. Turn on Proactive HA.
C. Set the Proactive HA Automation Level to Manual.
D. Set the Proactive HA Automation Level to Automated.
E. Turn on vSphere HA and vSphere DRS.
【多选题】
If vCenter Server 5.5 installation has one or more services deployed remotely, which three services are relocated to vCenter Server 6.5 on upgrade? (Choose three.)___
A. vCenter Inventory Services
B. vSphere Authentication Proxy
C. vSphere Web Client
D. vSphere
E. SXi Dump Collector
【多选题】
What two debugging levels can a virtual machine be configured to? (Choose two.)___
A. Verbose
B. Debugging
C. Statistics
D. Trivia
【多选题】
What are three benefits of using a few large-capacity LUNs instead of many small-capacity LUNs? (Choose three.) ___
A. Better performance because there is less contention for a single volume.
B. More flexibility for resizing virtual disks.
C. Less wasted storage space.
D. More flexibility to create virtual machines without adding new LUNs.
E. Fewer VMFS datastores to manage.
【多选题】
Which two configurable options are available in Boot Options for a virtual machine? (Choose two.)___
A. Tools Upgrades
B. Encryption
C. Firmware
D. Force BIOS setup
【多选题】
Which three VMware-recommended best practices should an administrator follow before upgrading to vSphere 6.5? (Choose three.)___
A. Disconnect ESXi host from vCenter.
B. VMware Tools are installed in the virtual machine.
C. Ensure that the system hardware complies with ESXi requirements.
D. Back up the host.
E. Check the interoperability of any other software integrated with vSphere.
【多选题】
What are two requirements to enable EVC in vSphere DRS cluster? (Choose two.)___
A. CPUs must be from the same vendor.
B. EVC must use the lowest possible baseline supported by the hardware.
C. CPUs must be in the same family and of the same speed.
D. No VMs may be running in the cluster.
【多选题】
What three conditions could result in VMware Flash Read Cache being unable to claim a disk? (Choose three.)___
A. The disk is not listed in the VMware hardware compatibility guide.
B. The disk is not detected as an SSD.
C. The disk is not detected as local.
D. The disk is in use by VMFs.
【多选题】
Boot from SAN is supported on which three storage technologies? (Choose three.)___
A. VMware vSAN
B. FCoE
C. NFS 4.1
D. iSCSI
E. FC
【多选题】
Which two components are part of storage I/O multipathing on ESXi? (Choose two.)___
A. SATP
B. VASA
C. PSP
D. VAAI
【多选题】
Which two statements are true about Highly Available vSphere Auto Deploy infrastructure? (Choose two.)___
A. It helps prevent data loss.
B. It is a prerequisite for using vSphere Auto Deploy with stateful install.
C. It requires two or more Auto
D. eploy servers.
【多选题】
The virtual machine log rotation size can be changed for all VMs by which two interfaces? (Choose two.)___
A. PowerCLI
B. vSphere Web Client
C. ESXi host client
D. esxcli
【多选题】
Which two configuration options can exclude virtual disks from snapshot operations? (Choose two.)___
A. Use RDM in virtual mode for virtual disk.
B. Use virtual disks in Independent – Persistent mode.
C. Use a virtual disk larger than 2 TB in size.
D. Use RDM in physical mode for virtual disk.
【多选题】
Which two storage configurations on the source server are unsupported with VMware Converter? (Choose two.)___
A. Linux LVM
B. software RAID
C. GPT/MBR hybrid disks
D. Windows basic volumes
E. Windows dynamic volumes
【多选题】
Which two statements about vCenter HA are correct? (Choose two.)___
A. ESXi 5.5 or later is required.
B. vCenter HA network latency between nodes must be less than 50 ms.
C. NFS datastore is supported.
D. It must be deployed on a 3
E. SXi host cluster with DRS enabled.
【多选题】
An attempt to delete NFS datastore from a ESXi host returns the error: Sysinfo error on operation returned the following status:< Busy> Which two statements could explain this failure? (Choose two.)___
A. NFS datastore is a part of Storage DRS Cluster.
B. NFS.VolumeRemountFrequency value is set to 30.
C. Storage I/O Control is enabled on NFS datastore.
D. NFS datastore has running or registered virtual machines.
【多选题】
An administrator finds that the Microsoft Exchange virtual machines are exhibiting network latency. What two in-guest changes can help decrease latency? (Choose two.)___
A. LRO
B. TSO
C. SR-IOV
D. PVRDMA
【多选题】
Which two types of iSCSI adapters require VMkernel networking configuration? (Choose two.)___
A. dependent hardware
B. in-guest
C. software
D. independent hardware
【多选题】
Which two statements are true for NFS v4.1 firewall behavior? (Choose two.)___
A. It closes port 2049.
B. It sets allowed. All flag to TRUE.
C. It sets allowed. All flag to FALSE.
D. It opens port 2049.
【多选题】
A vSphere Administrator attempts to enable Fault Tolerance for a virtual machine but receives the following error: Secondary VM could not be powered on as there are no compatible hosts that can accommodate it. What two options could cause this error? (Choose two.)___
A. The other ESXi host(s) are in Maintenance Mode.
B. Hardware virtualization is not enabled on the other ESXi host(s).
C. The other ESXi host(s) are in Quarantine Mode.
D. Hardware MMU is enabled on the other
E. SXi host(s).
【多选题】
Storage capabilities be populated in what two ways? (Choose two.)___
A. The administrator can use tags to describe capabilities.
B. Default capabilities are provided by vCenter Server.
C. Datastores can advertise their capabilities through VAAI.
D. Datastores can advertise their capabilities through VASA.
【多选题】
In network troubleshooting it is important to know what upstream switch the ESXi host is connected to. Which two features does ESXi provide to help identify the upstream switch? (Choose two.)___
A. Promiscuous mode
B. DPM
C. LLDP
D. CDP
【多选题】
Virtual Volumes supports which three VMware features? (Choose three.)___
A. Instant Clones
B. Distributed Resource Scheduler
C. Linked Clones
D. vMotion
E. Storage Distributed Resource Scheduler
【多选题】
vSphere DRS helps to balance virtual machines with available resources in a vSphere cluster. What three types of resources can be taken into account for balancing? (Choose three.)___
A. CPU
B. physical NIC saturation of an ESXi host
C. virtual NIC saturation of a virtual machine
D. RAM
E. storage latency
【多选题】
Which three design requirements must be satisfied to enable RAID-6 objects in a VMware vSAN cluster? (Choose three.)___
A. vSAN Advanced license or higher
B. vSAN stretched cluster
C. at least six hosts contributing storage
D. deduplication and compression
E. all flash configuration
【多选题】
When using "Cluster resource percentage" for host failover capacity in vSphere HA Admission Control, the total resource requirements are calculated from which two values? (Choose two.)___
A. Total vCPUs assigned to each VM.
B. Average CPU usage on each VM over time.
C. Memory reservations on each VM.
D. Total memory assigned to each VM.
E. Average active memory on each VM over time.
F. CPU reservations on each VM.
【多选题】
Which are four attributes of the Active vCenter HA node? (Choose four)___
A. It uses the vCenter HA network to communicate with the Witness node.
B. It constantly replicates vPostgres data with the Witness node.
C. It uses a public IP address for the management interface.
D. It runs the active vCenter Server Appliance instance.
E. It uses the vCenter HA network for replication of data to the Passive node.
F. It provides a quorum to protect against split-brain situations.
【多选题】
Which are two vCenter Server two-factor authentication methods? (Choose two.)___
A. RSA SecurID
B. Smart Card
C. SAML
D. Symantec VIP
推荐试题
【单选题】
下列有关光学平直仪说法错误的是___。
A. 光学平直仪是由平直仪本体和反射镜组成
B. 光学平直仪是一种精密光学测量仪器
C. 光学平直仪可以同时测出工件水平方向和水平垂直的方向的直线性
D. 光学平直仪不能测出滑板运动的直线性
【单选题】
变量录能实现流量的调节,其主要原因是因为___。
A. 密封容积的存在
B. 密封容积的变化
C. 电机转速的变化
D. 密封容积的变化量可调
【单选题】
由于静压轴承节流器间隙被杂物堵塞,流油不畅造成轴承油腔压力不稳定可通过___方法解决。
A. 清洗节流器
B. 清洗滤油器
C. 更换轴承
D. 调整膜片间隙
【单选题】
在床身纵向导轨的专用检具上放自准直仪的反射镜,光管放在床身的外面,___转至测量垂直平面直线度的 A处,移动检具,每隔检具长度记录一次读数,并画出导轨的误差曲线。
A. 光管
B. 观察镜
C. 读数头
D. 反射镜
【单选题】
___是由链条和具有特殊齿形的链轮组成的传递运动和动力的传动。
A. 齿轮传动
B. 链传动
C. 螺旋传动
D. 带传动
【单选题】
液压系统回油站中背压___时,将会产生液压系统的振动而影响加工工件的精度。
A. 很小
B. 很大
C. 适当
D. 无法确定
【单选题】
利用火焰、电弧等热源、将金属或非金属材料加热到熔融状态,在高速气流的推动下,呈雾状___到工件表面上的过程称为金属喷涂。
A. 洒落
B. 散落
C. 喷落
D. 喷射
【单选题】
M1432A 型磨床工作台换向时,先导阀已改变方向,但换向阀不动作,因而工作台不换向,其原因是___。
A. 停留阀节流口太大
B. 主油路压力低
C. 辅助油路压力低
D. 泵的压力高
【单选题】
两孔轴线相交成90°角,一个孔直径为φ20mm,另一个孔直径是φ30mm,以下___是不正确的工艺。
A. 用万能角度尺和心轴检测两孔轴线角度是否合格
B. 用宽座角尺、心轴和塞尺检测两孔轴线角度是否合格
C. 用百分表和心轴检测两孔轴线角度是否合格
D. 用千分尺和心轴检测两孔轴线角度是否合格
【单选题】
深孔,是指孔的深度和直径的比值___的孔。
A. 等于5
B. 等于4
C. 大于5小于20
D. 大于20
【单选题】
高速旋转机械的启动试运转,通常不能突然加速,也不能在短时间内升速至___。
A. 最低转速
B. 最高转速
C. 额定工作转速
D. 最低或最高转速
【单选题】
在轴颈上钻孔时,先将定心工具夹持在钻床主轴上找正V型铁的中心并固定,然后把轴卧放在V型铁中,用___按工件端面中心线找正并固定,最后移动钻头就可以钻孔了。
A. 宽座角尺
B. 钢板直尺
C. 刀口尺
D. 水平仪
【单选题】
班组的费用核算主要是指更换配件,材料,改造未预见的更换件,配件和材料。这些费用若计算在承包费或额定工时内,则要从___的原则出发,既在保证周期,保证质量的前提下,尽可能少换多修,多代少领。
A. 节约材料
B. 节约能源
C. 节约费用
D. 节约成本
【单选题】
在板牙套入工件2~3牙后,应及时从___方向用90°角尺进行检查,并不断校正至要求。
A. 前后
B. 左右
C. 前后、左右
D. 上下、左右
【单选题】
机床主轴轴承特别是现代数控机床主轴轴承绝大部分采用了___润滑。
A. 润滑油 
B. 柴油
C. 润滑脂 
D. 机油
【单选题】
用薄板钻钻削工件时,___,起定心和箝制作用。
A. 钻心尖先切入工件
B. 钻外尖先切入工件
C. 钻心尖和钻外尖同时切入工件
D. 有时钻心尖先切入工件,有时钻外尖先切入工件
【单选题】
一些特种机床的精密丝杠常选用38CrMoAlA材料制造,其热处理工艺是调质H B280,渗氮HV850,调质后基体组织必须是均匀的___,渗氮前表面应无脱碳层。
A. 索氏体
B. 贝氏体
C. 马氏体
D. 奥氏体
【单选题】
要将齿轮断裂的齿轮修复如断,则以下修复工艺原则中,哪个是不正确有修复原则___
A. 修复工艺要考虑新齿模数与原齿轮必须一样
B. 修复工艺要考虑新齿材料与原齿轮必须一样
C. 新齿齿廓的硬度必须大于原齿廓
D. 新齿齿廓的硬度必须等于原齿廓
【单选题】
采用定向装配的方法装配滚动轴承时,在装配前需对主轴轴端锥孔中心线偏差及___进行测量,确定误差方向并作好标记。
A. 轴承内、外圈径向跳动误差
B. 轴承内孔与外圈的同心度误差
C. 轴承外圈尺寸误差
D. 轴承内孔尺寸误差
【单选题】
班组的经济核算无论是项目承包或单台总工时的考核,还是按计划,经济地完成任务,都需要以降低成本,提高质量,缩短修理周期为班组的___,这也是班组经济换算的关键。
A. 生产要求
B. 工作要求
C. 生产目标
D. 工作目标
【单选题】
经纬仪在机械装配和修理中,主要是用来检测精密机床的___和万能转台的分度误差。
A. 水平转台
B. 垂直转台
C. 水平导轨
D. 垂直导轨
【单选题】
下列对管道工安全操作规程表述不正确的是___。
A. 绞管牙时,人应站在绞柄前面,锯割管子在快要割断时不要用力要猛,以使其快速断开
B. 不允许一人单独在沟、井及容器内作业,必须有二人以上,其中一人在外面负责.监护
C. 在沟、井、容器内工作的人员,如发现有异味或感到头晕、恶心等,应即停止工作到外面休息,待处理后再进入工作,有条件的地方应搞好通风
D. 在有压力的管道上抢修时,,应先进行减压,正在运行的管道(汽、水)原则上不允许进行检修工作
【单选题】
在数控机床的试运行中,除了___引起的故障外,则不允许机床有故障出现,否则表明机床的安装调试有问题。
A. 软件
B. 硬件
C. 机床运动特性
D. 操作失误
【单选题】
合理调整轴承间隙,是保证轴承寿命,提高轴的___的关键。
A. 旋转速度
B. 旋转精度
C. 尺寸精度
D. 表面粗糙度
【单选题】
滚齿机检测时外支架置于工作行程上端,检验棒安放在工作台上,固定指示器,使其测头分别在 A、 B位置垂直接触及相距L2处的检验棒表面,移动外支架,顶紧检验棒检验,将工作台回转___,再检验一次。
A. 90°
B. 150°
C. 100°
D. 180°
【单选题】
喷吸钻是一种新型的内排屑深孔钻,主要用于加工直径___的深孔。
A. 直径为18~180mm,深径比在100mm以内
B. 直径为10~80mm,深径比在50mm以内
C. 直径为10~100mm,深径比在150mm以内
D. 直径为10~150mm,深径比在100mm以内
【单选题】
以下工件的毛坯生产过程中,哪些最适合锻镦粗___
A. 单个圆盘形齿轮
B. 双联圆盘形齿轮
C. 法兰盘
D. 圆柱光短轴
【单选题】
一些特种机床的精密丝杠常选用38CrMoAlA材料制造,其热处理工艺是调质H B280,渗氮HV850,调质后基体组织必须是均匀的___,渗氮前表面应无脱碳层。
A. 索氏体
B. 贝氏体
C. 马氏体
D. 奥氏体
【判断题】
读装配图,首相应了解各零件的连接形式及装配关系
A. 对
B. 错
【判断题】
全跳动和圆跳动是表示工件的形状公差
A. 对
B. 错
【判断题】
用来表达机件的倾斜部分结构形状的视图称为旋转试图
A. 对
B. 错
【判断题】
球面可展开成曲面,能准确地画出展开图
A. 对
B. 错
【判断题】
对照视图仔细研究不见的装配关系和工作原理,是读装配图的一个重要环节
A. 对
B. 错
【判断题】
合像水平仪是一种用来测量对水平位置或垂直位置微小偏差的几何量仪
A. 对
B. 错
【判断题】
从原先上讲,自准直量仪实际是添装了目镜的平行光管
A. 对
B. 错
【判断题】
光学平直仪中,望远镜的焦距越短,目镜越长,放大率就越大
A. 对
B. 错
【判断题】
测微准直望远镜的光轴与外镜管几何轴线的同轴度误差大雨0.05mm,平行度误差大于3″
A. 对
B. 错
【判断题】
空气进入液压系统,不仅会造成运动不见的爬行,而且回引起冲击现象
A. 对
B. 错
【判断题】
通常油泵的吸油口装精滤油器,出口装粗滤油器
A. 对
B. 错
【判断题】
严格控制油缸与活塞之间的配合间隙,是防止泄露和保证运动可靠的关键
A. 对
B. 错