【判断题】
CO2 气体保护焊是一种用 CO2液体作为保护熔化极的电弧焊方法
A. 对
B. 错
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【判断题】
CO2 气体保护焊主要用于焊接低碳钢及低合金高强钢,也可以用于焊接耐热钢和不锈钢,可进行自动焊及半自动焊
A. 对
B. 错
【判断题】
钨极氩弧焊是以钨棒作为电弧的一极的电弧焊方法,钨棒在电弧焊中是不熔化的,故又称不熔化极氩弧焊,简称 TIG焊
A. 对
B. 错
【判断题】
由于被惰性气体隔离,焊接区的熔化金属不会受到空气的有害作用,所以钨极氩弧焊可用以焊接易氧化的有色金属如铝、镁及其合金
A. 对
B. 错
【判断题】
埋弧焊电弧产生于堆敷了一层的焊剂下的焊丝与零件之间,受到熔化的焊剂——熔渣以及金属蒸汽形成的气泡壁所包围
A. 对
B. 错
【判断题】
相比焊条电弧焊,埋弧焊的主要优点:焊接电流和电流密度大,生产效率高,是手弧焊生产率的 50~100 倍
A. 对
B. 错
【判断题】
埋弧焊自动化水平高,但有弧光辐射,工人劳动条件不好
A. 对
B. 错
【判断题】
埋弧焊不受到焊剂敷设限制,可以用在空间位置焊缝的焊接
A. 对
B. 错
【判断题】
由于埋弧焊焊剂的成分主要是 MnO 和 SiO2 等金属及非金属氧化物,适合焊铝、钛等易氧化的金属及其合金
A. 对
B. 错
【判断题】
埋弧焊在中、厚板对接、角接接头有广泛应用,14 mm以下板材对接可以不开坡口。埋弧焊也可用于合金材料的堆焊上
A. 对
B. 错
【判断题】
等离子弧按电源供电方式不同,分为两种形式
A. 对
B. 错
【判断题】
非转移型等离子弧:电极接电源正极,喷嘴接负极,而零件不参与导电。电弧是在电极和喷嘴之间产生
A. 对
B. 错
【判断题】
转移型等离子弧: 钨极接电源负极,零件接正极,等离子弧在钨极与零件之间产生
A. 对
B. 错
【判断题】
A. 对
B. 错
【判断题】
气焊是利用气体火焰加热并熔化母体材料和焊丝的焊接方法
A. 对
B. 错
【判断题】
气焊常用于薄板的低碳钢、低合金钢、不锈钢的对接、端接,在熔点较低的铜、铝及其合金的焊接中仍有应用
A. 对
B. 错
【判断题】
中性焰是当氧气与乙炔的混合比为 1~1.2 时,燃烧充分,燃烧过后无剩余氧或乙炔,热量集中,温度可达 2050℃~2150℃
A. 对
B. 错
【判断题】
中性焰焰心是呈亮白色的圆锥体,温度较低;内焰呈暗紫色,温度最高,适用于焊接;外焰颜色从淡紫色逐渐向橙黄色变化,温度下降,热量分散
A. 对
B. 错
【判断题】
碳化焰是指当氧气与乙炔的混合比小于 1 时,部分乙炔未曾燃烧,焰心较长,呈蓝白色,温度最高达 2700℃~3000℃
A. 对
B. 错
【判断题】
氧化焰是指当氧气与乙炔的混合比大于 1.2时,燃烧过后的气体仍有过剩的氧气,焰心短而尖,内焰区氧化反应剧烈,火焰挺直发出“嘶嘶”声,温度可达 2100℃~2300℃
A. 对
B. 错
【判断题】
氧化焰由于火焰具有氧化性,焊接碳钢易产生气体,并出现熔池沸腾现象,很少用于焊接
A. 对
B. 错
【判断题】
电阻焊是将零件组合后通过电极施加压力,利用电流通过零件的接触面及临近区域产生的电阻热将其加热到熔化或塑性状态,使之形成金属结合的方法
A. 对
B. 错
【判断题】
点焊方法:将零件装配成搭接形式,用电极将零件夹紧并通以电流,在电流热作用下,电极之间零件接触处被加热熔化形成焊点
A. 对
B. 错
【判断题】
凸焊 是电加热后突起点被压塌,形成焊接点的电阻焊方法
A. 对
B. 错
【判断题】
对焊工作原理:将两零件端部相对放置,加压使其端面紧密接触,通电后利用电阻热加热零件接触面至塑性状态,然后迅速施加大的顶锻力完成焊接
A. 对
B. 错
【判断题】
电渣焊是一种利用电流通过液体熔渣所产生的电阻热加热熔化填充金属和母材,以实现金属焊接的熔化焊接方法
A. 对
B. 错
【判断题】
电渣焊适用于厚板、大断面、曲面结构的焊接,如火力发电站数百吨的汽轮机转子、锅炉大厚壁高压汽包等
A. 对
B. 错
【判断题】
激光焊是利用大功率相干单色光子流聚集而成的激光束为热源进行焊接的方法
A. 对
B. 错
【判断题】
焊接时,焊件仅在局部区域被加热到高温,离焊缝愈远,温度愈高,膨胀也愈大
A. 对
B. 错
【判断题】
焊接产生拉应力和压应力,当这些应力超过金属的强度极限时,将产生焊接变形;当超过金属的屈服极限时,则会出现裂缝
A. 对
B. 错
【判断题】
未焊透是指工件与焊缝金属或焊缝层间局部未熔合的一种缺陷
A. 对
B. 错
【判断题】
裂纹是最危险的一种缺陷,它除了减少承载截面之外,还会产生严重的应力集中,在使用中裂纹会逐渐扩大,最后可能导致构件的破坏
A. 对
B. 错
【判断题】
孔加工刀具都应同时完成两个运动。主运动,即沿着轴线方向对着零件的直线运动;进给运动,即刀具刀具绕轴线的旋转运动
A. 对
B. 错
【判断题】
CO2 气体保护焊设备可分为手动焊和自动焊两种类型
A. 对
B. 错
【判断题】
以惰性气体氩气作保护气的电弧焊方法有钨极氩弧焊和熔化极氩弧焊两种
A. 对
B. 错
【判断题】
由于被惰性气体隔离,焊接区的熔化金属不会受到空气的有害作用,所以钨极氩弧焊可用以焊接易氧化的有色金属如铝、镁及其合金
A. 对
B. 错
【判断题】
埋弧焊电弧产生于堆敷了一层的焊剂下的焊丝与零件之间,受到熔化的焊剂—熔渣以及金属蒸汽形成的气泡壁所包围
A. 对
B. 错
【判断题】
埋弧焊主要优点是焊接电流和电流密度大,生产效率高,是手弧焊生产率的 1~2 倍
A. 对
B. 错
【判断题】
气焊是利用气体火焰加热并熔化母体材料和焊条的焊接方法
A. 对
B. 错
【判断题】
锯条一般用工具钢或合金钢制成,并经淬火和高温回火处理
A. 对
B. 错
【判断题】
锯条规格用锯条两端安装孔之间距离表示,并按锯齿齿距分为粗齿、细齿二种
A. 对
B. 错
推荐试题
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。
A. 四相
B. 三相
C. 两项
D. 单相
【单选题】
24.对于工作环境恶劣、启动频繁的异步电动机,所用热继电器热元件的额定电流可选为电动机额定电流的___倍。
A. 0.95~1.05
B. O.85~0.95
C. 1.05~1.15
D. 1.15~1.50
【单选题】
25.中间继电器的选用依据是控制电路的___、电流类型、所需触点的数量和容量等。
A. 短路电流
B. 电压等级
C. 阻抗大小
D. 绝缘等级