【单选题】
第一种工作票应在工作日___送达运行人员
A. 当天
B. 前一天
C. 工作前
D. 前两天
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
同一变电站内在几个电气连接部分上依次进行不停电的同一类型的工作,可以使用一张___
A. 第二种工作票
B. 第一种工作票
C. 带电作业工作票
D. 事故应急抢修单
【单选题】
变更工作负责人或增加工作任务,如工作签发人无法当面办理,应通过电话联系,并在___注明
A. 值班记录
B. 派工单
C. 设备巡回检查记录
D. 工作登记薄和工作票上
【单选题】
第一种、第二种工作票能延期___次
A. 一
B. 二
C. 三
D. 四
【单选题】
在未办理工作终结手续以前,___不准将停电设备合闸送电
A. 监护人
B. 负责人
C. 许可人
D. 任何人
【单选题】
工作间断时,工作班人员应从工作现场撤出,所有安全措施保持不动,工作票仍由___执存
A. 工作许可人
B. 工作负责人
C. 工作签发人
D. 专责监护人
【单选题】
已终结的工作票、事故抢修单应保存___
A. 半年
B. 一年
C. 三个月
D. 两年
【单选题】
只有在同一停电系统的所有工作票都已终结,汇报调度并得到___许可指令,方可合闸送电
A. 工作负责人
B. 工作许可人
C. 值班调度员
D. 工作签发人
【单选题】
小组工作票应一式两份,由___分别收执。
A. 工作负责人和工作许可人
B. 工作负责人和工作票签发人
C. 工作负责人和小组工作负责人
D. 工作负责人和当值调度员
【单选题】
小组工作票上所列的安全措施应与第一种工作票上所列的安全措施___
A. 相符
B. 互为补充
C. 可以不符
D. 任意
【单选题】
在门型构架的线路侧进行停电检修,如工作地点与所装接地线的距离小于___米,工作地点虽在接地线外侧,也可不另装接地线。
A. 10
B. 12
C. 15
D. 18
【单选题】
高压回路上的工作,必须要拆除全部或一部分接地线后方可工作者,应征得___的许可(根据调度员指令装设的接地线,应征得调度员的许可),方可进行
A. 签发人
B. 负责人
C. 许可人
D. 运行人员
【单选题】
如果线路上有人工作,应在线路断路器和隔离开关操作把手上,均悬挂___
A. 禁止合闸,线路有人工作
B. 禁止合闸 ,有人工作
C. 禁止分闸
D. 在此工作
【单选题】
室内母线分段部分母线交叉部分容易碰到有电设备的,应设有明显标志的___隔离挡板
A. 临时 性
B. 暂时性
C. 永久性
D. 随意性
【单选题】
倒闸操作应根据___或运行值班负责人的指令,受令人复诵无误后执行
A. 工作负责人
B. 工作签发人
C. 值班调度员
D. 值班领导
【单选题】
雷雨天气,需要巡视室外高压设备时,应穿___,并不准靠近避雷器和避雷针
A. 绝缘靴
B. 戴绝缘手套
C. 绝缘鞋
D. 皮鞋
【单选题】
倒闸操作由___填写操作票
A. 值班调度
B. 值班领导
C. 操作人员
D. 运行人员
【单选题】
用绝缘棒拉合隔离开关,均应戴___
A. 护目镜
B. 绝缘手套
C. 安全帽
D. 线手套
【单选题】
交流滤波器(并联电容)退出运行后再次投入运行前,应满足电容___时间要求
A. 充电
B. 放电
C. 存放
D. 闲置
【单选题】
下列工作 可以不用操作票___
A. 拉合断路器的单一操作
B. 在运行的高压设备上工作
C. 在二次回路上工作
D. 装卸高压熔断器
【单选题】
线路停、送电均应按照___或线路工作许可人的指令执行
A. 值班调度员
B. 工作负责人
C. 值班领导
D. 变电值班员
【单选题】
当用户管辖的线路要求停电时,应得到___的申请,经批准后方可停电
A. 申请人
B. 用户
C. 用户停送电联系人
D. 变电站
【单选题】
当用户管辖的线路要求恢复送电,应接到___的工作结束报告,做好录音并记录后方可进行
A. 原申请人
B. 用户
C. 用户停送电联系人
D. 变电站
【单选题】
装有SF6设备的配电装置室和SF气体实验室,应装设强力通风装置,风口应设置在室内___
A. 底部
B. 中间
C. 上部
D. 窗户旁
【单选题】
在室内,设备充装SF6气体时,周围环境相对湿度应不大于___%,同时应开启通风系统
A. 80
B. 70
C. 90
D. 95
【单选题】
SF配电室及下方电缆层隧道的门上,应设置___
A. 从此进入
B. 在此工作
C. 注意通风
D. 止步危险
【单选题】
工作区空气中SF6气体含量不得超过___UL/L
A. 800
B. 1000
C. 1200
D. 1400
【单选题】
工作人员进入SF配电室,入口处若无SF气体含量显示器,应先通风___分钟,并用检漏仪测量SF气体含量合格
A. 5
B. 8
C. 10
D. 15
【单选题】
填写变电站第一种工作票的工作___
A. 在高压设备继电保护上工作,需高压停电工作
B. 安装自动装置上的工作,不停用所保护高压设备
C. 在运行设备的二次回路上进行拆、接线工作
D. 低压配电盘、配电箱上的工作
【单选题】
在带电的电流互感器二次回路上工作时,应设有专人监护,使用绝缘工具,并站在___
A. 凳子上
B. 梯子上
C. 绝缘垫上
D. 设备上
【单选题】
高压试验,试验现场应装设围栏,向外悬挂___的标示牌
A. 在此工作
B. 禁止攀登,高压危险
C. 止步,高压危险
D. 从此进入
【单选题】
高压直流实验间断时,应将设备对地数次放电并___
A. 数次加压
B. 从新试验
C. 短路接地
D. 接地
【单选题】
填写变电站第二种工作票的工作___
A. 高压电力电缆需停电的工作
B. 二次系统和照明回路上工作,需要将高压停电
C. 非运行人员在高压回路上使用钳形电流测量
D. 自动化监控系统工作需将高压设备停电
【单选题】
在测量高压电缆各相电流时,电缆头线间距离应在___mm以上
A. 100
B. 150
C. 200
D. 300
【单选题】
电力电缆试验要拆除接地线时,应征得___的许可(根据调度员指令装设的接地线,应征得调度员的许可),方可进行
A. 工作负责人
B. 工作许可人
C. 操作人员
D. 现场领导
【单选题】
风力大于___级是不宜带电作业
A. 3
B. 4
C. 5
D. 2
【单选题】
六氟化硫回收时作业人员应站在___。
A. 下风侧
B. 上风侧
C. 左侧
D. 右侧
【单选题】
串联电容器及与整组电容器脱离的电容器应___放电
A. 及时
B. 逐个单次
C. 逐个多次
D. 整体
【单选题】
电缆耐压试验更换试验引线时,作业人员应穿戴好___
A. 绝缘鞋
B. 安全帽
C. 绝缘手套
D. 护目镜
【单选题】
手持电动工具在三相四线制系统中应使用___芯软橡胶电缆
A. 三
B. 四
C. 二
D. 五
【单选题】
所有升降口、大小孔洞、楼梯和平台。应装设不低于___mm高的栏杆
A. 700
B. 800
C. 900
D. 1050
推荐试题
【单选题】
Which path do you follow to enable aaa through the SDM ?___
A. Configure Tasks > AAA
B. Configure > Addition Authentication > AAA
C. Configure > AAA
D. Configure > Additional Tasks > AAA
E. Configure Authentication > AAA
【单选题】
which technology cloud be used on top of an MPLS VPN to add confidentiality ?___
A. IPsec
B. 3DES
C. AES
D. SSL
【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
【单选题】
You have just deployed SNMPv3 in your environment, Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request?___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port?___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5