【单选题】
按逻辑功能的不同,双稳态触发器可分为___。
A. RS、JK、D、T等
B. 主从型和维持阻塞型
C. TTL型和MOS型
D. 上述均包括
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
同步计数器和异步计数器比较,同步计数器的显著优点是___。
A. 工作速度高
B. 触发器利用率高
C. 电路简单
D. 不受时钟CP控制。
【单选题】
把一个五进制计数器与一个四进制计数器串联可得到___进制计数器。
A. 4
B. 5
C. 9
D. 20
【单选题】
下列逻辑电路中为时序逻辑电路的是___ 。
A. 变量译码器
B. 加法器
C. 数码寄存器
D. 数据选择器
【单选题】
47N个触发器可以构成最大计数长度{进制数}为___ 的计数器。
A. N
B. 2N
C. N2
D. 2N
【单选题】
N个触发器可以构成能寄存___位二进制数码的寄存器。
A. N-1
B. N
C. N+1
D. 2N
【单选题】
49五个D触发器构成环形计数器,其计数长度为___。
A. 5
B. 10
C. 25
D. 32
【单选题】
同步时序电路和异步时序电路比较,其差异在于后者___。
A. 没有触发器
B. 没有统一的时钟脉冲控制
C. 没有稳定状态
D. 输出只与内部状态有关
【单选题】
一位8421BCD码计数器至少需要___个触发器。
A. 3
B. 4
C. 5
D. 10
【单选题】
某电视机水平-垂直扫描发生器需要一个分频器将31500HZ的脉冲转换为60HZ的脉冲,欲构成此分频器至少需要___个触发器。
A. 10
B. 60
C. 525
D. 31500
【单选题】
555定时器属于___
A. 时序逻辑电路
B. 组合逻辑电路
C. 模拟电子电路
【单选题】
54多谐振荡器可产生 ___
A. 正弦波
B. 矩形脉冲
C. 三角波
D. 锯齿波
【单选题】
脉冲整形电路有___。
A. 多谐振荡器
B. 施密特触发器
C. 555定时器
【单选题】
56石英晶体多谐振荡器的突出优点是___ 。
A. 速度高
B. 电路简单
C. 振荡频率稳定
D. 输出波形边沿陡峭
【单选题】
TTL单定时器型号的最后几位数字为___。
A. 555
B. 556
C. 7555
D. 7556
【单选题】
555定时器不可以组成___。
A. 多谐振荡器
B. 单稳态触发器
C. 施密特触发器
D. JK触发器
【单选题】
59以下各电路中,___可以产生脉冲定时。
A. 多谐振荡器
B. 单稳态触发器
C. 施密特触发器
D. 石英晶体多谐振荡器
【单选题】
555定时电路端不用时,应当___。
A. 接高电平
B. 接低电平
C. 通过0.01µF的电容接地
D. 通过小于500Ω的电阻接地
【单选题】
89S51的内部程序存储器与数据存储器容量各为多少?___
A. 64KB、128B
B. 4KB、64KB
C. 4KB、128B
D. 8KB、256B
【单选题】
89S51比89C51多出了哪个功能?___
A. 存储器加倍
B. 具有WDT工能
C. 多了一个8位输入/输出端口
D. 多了一个串行口
【单选题】
6在DIP40封装的8×51芯片里,复位RESET引脚的引脚编号是什么?___
A. 9
B. 19
C. 29
D. 39
【单选题】
7在DIP40封装的8×51芯片里,接地引脚与电源引脚的引脚编号是什么?___
A. 1、21
B. 11.31
C. 20、40
D. 19、39
【单选题】
9在12MHz始终脉冲的8051系统里,一个机器周期有多长?___
A. 1µs
B. 12µs
C. 1ms
D. 12ms
【单选题】
12下列哪个寄存器是8×51内的16位寄存器?___
A. CC
B. C
C. PC
D. R7
【单选题】
14在8×51的输入/输出端口里,哪个输入/输出端口执行在输出功能时没有内部上拉电阻?___
A. P0
B. P1
C. P2
D. P3
【单选题】
8×51的P0采用哪种电路结构?___
A. 集电极开路式输出
B. 基极开路式输出
C. 发射机开路式输出
D. 图腾柱输出
【单选题】
17在8×51里,若要扩展外部存储器时,数据总线连接哪个输入/输出端口?___
A. P0
B. P1
C. P2
D. P3
【单选题】
点亮一般的LED所耗用的电流约为多少?___
A. 1~5µA
B. 10~20µA
C. 1~5mA
D. 10~20mA
【单选题】
19一般地,蜂鸣器属于哪种负载?___
A. 电阻性负载
B. 电感性负载
C. 电容性负载
D. 不导电负载
【单选题】
7405/7406的输出采用哪种电路结构?___
A. 集电极开路式输出
B. 基极开路式输出
C. 发射机开路式输出
D. 图腾柱输出
【单选题】
21在继电器中,NO接点是一种什么接点?___
A. 不使用接点
B. 不存在接点
C. 激磁后即开路的接点
D. 常开接点
【单选题】
22所谓2P的继电器,代表什么意思?___
A. 只有2个接点
B. 两相的负载
C. 两组电源
D. 2组c接点
【单选题】
23共阳极七段数码管显示器的驱动信号有何特色?___
A. 低电平点亮
B. 低电平不亮
C. 高电平点亮
D. 以上皆非
【单选题】
24在8×51的程序里,若要将某个输入/输出端口设置成输入功能,应如何处理?___
A. 先输出高电平到该输入/输出端口
B. 先输出低电平到该输入/输出端口
C. 先读取该输入/输出端口的状态
D. 先保存该输入/输出端口的状态
【单选题】
8×51提供几个外部中断和定时器/计数器中断?___
A. 2,2
B. 3,6
C. 2,3
D. 3,7
【单选题】
8×51的IP缓存器的功能如何?___
A. 设置中断优先级
B. 启动中断功能
C. 设置中断触发信号
D. 定义CPU的网址
【单选题】
28若要让采用低电平触发,则应如何设置?___
A. EX0=0
B. EX0=1
C. IT0=0
D. IT0=1
【单选题】
29在Keil µVision3里进行调试/仿真时,在哪里操作才能触动程序中断?___
A. 在Interrupt System
B. 在Cotorl Box对话框里
C. 直接单击魔术棒按钮即可
D. 直接按0键
【单选题】
30在8×51所提供的中断功能里,下列哪个优先级比较高?___
A. T1
B. RI/TI
C. T0
D. INT0
【单选题】
31在TCON缓存里,IE1的功能是什么?___
A. 触发 IE1中断
B. 指示IE1中断的标志
C. 提高IE1优先等级
D. 取消IE1中断
【单选题】
32在Keil C里,中断子程序与函数又何不同?___
A. 中断子程序不必声明
B. 函数不必声明
C. 中断子程序必须有形式参数
D. 中断子程序一定会有返回值
推荐试题
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。
A. 四相
B. 三相
C. 两项
D. 单相