【单选题】
___0152.使用移动电气设备和手持电动工具时，开关箱内应按规定安装（ ）。
A. 漏电保护装置
B. 避雷器
C. 电涌
D. 接闪器
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
___0160.插拔插头时，应保证电气设备和电气装置处于（ ），同时人体不得（ ）插头的导电极，并避免对电源线施加外力。
A. 工作状态；靠近
B. 工作状态；触及
C. 非工作状态；靠近
D. 非工作状态；触及
【单选题】
___0166.关于手持电动工具说法错误的是（ ）。
A. 使用时，操作者应采取必要的防护措施
B. 在狭窄作业场所操作时，可无人监护
C. 在湿热、雨雪等作业环境，应使用具有相应防护等级的工具
D. 工具的电源线不得任意接长或拆换
【单选题】
___0173.《低压配电设计规范》（GB 50054—2011）规定，采用剩余电流动作保护电器作为间接接触防护电器的回路时，（ ）装设保护导体。
A. 必须
B. 严禁
C. 可
D. 不宜
【单选题】
___0174.《低压配电设计规范》（GB 50054—2011）规定，保护接地中性导体应按（ ）进行绝缘。
A. 实际出现的最低电压
B. 实际出现的最高电压
C. 预期出现的最低电压
D. 预期出现的最高电压
【单选题】
___0176.《低压配电设计规范》（GB 50054—2011）规定，同一配电室内相邻的两段母线，当任一段母线有一级负荷时，相邻的两端母线之间应采取（ ）措施。
A. 防雷
B. 防潮
C. 防噪声
D. 防火
【单选题】
___0177.《低压配电设计规范》（GB 50054—2011）规定，高压及低压配电设备设在（ ）室内，且两者有一侧柜有裸露的母线时，两者之间的净距不应（ ）2m。
A. 同一；大于
B. 同一；小于
C. 不同；大于
D. 不同；小于
【单选题】
___0180.根据《电业安全工作规程 第1部分：热力和机械》（GB 21—2010）规定，电业工作场所（ ）利用任何管道、栏杆、脚手架悬吊重物和起吊设备。
A. 必须
B. 禁止
C. 可
D. 不宜
【单选题】
___0182.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），闪点是指在标准条件下，使液体变成蒸汽的数量能够形成可燃性气体或空气混合物的（ ）液体温度。
A. 最低
B. 最高
C. 一般
D. 平均
【单选题】
___0183.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），引燃温度是指可燃性气体与蒸汽与空气形成的混合物，在规定条件下被热表面引燃的（ ）温度。
A. 最低
B. 最高
C. 一般
D. 平均
【单选题】
___0184.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），（ ）是指物质本身是可燃性的，能够产生可燃性气体、蒸气或薄雾。
A. 可燃性物质
B. 可燃性气体或蒸气
C. 可燃液体
D. 可燃薄雾
【单选题】
___0185.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），（ ）是指在大气条件下，气体、蒸气、薄雾状的可燃物质与空气的混合物，引燃后燃烧将在全范围内传播。
A. 高挥发性液体
B. 爆炸性气体混合物
C. 爆炸性气体环境
D. 爆炸危险区域
【单选题】
___0186.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），（ ）是指在大气条件下，气体或蒸气可燃物质与空气的混合物引燃后，能够保持燃烧自行传播的环境。
A. 高挥发性液体
B. 爆炸性气体混合物
C. 爆炸性气体环境
D. 爆炸危险区域
【单选题】
___0187.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），（ ）是指爆炸性混合物出现的或预期可能出现的数量达到足以要求对电气设备的结构、安装和使用采取预防措施的区域。
A. 爆炸性气体环境
B. 非爆炸性气体环境
C. 爆炸危险区域
D. 非爆炸危险区域
【单选题】
___0188.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），（ ）是指在空气中能燃烧或无焰燃烧并在大气压和正常温度下能与空气形成爆炸性混合物的粉尘、纤维或飞絮。
A. 可燃性粉尘
B. 导电性粉尘
C. 可燃性飞絮
D. 爆炸性粉尘环境
【单选题】
___0189.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），（ ）是指在大气环境条件下，可燃性粉尘与空气形成的混合物被点燃后，能够保持燃烧自行传播的环境。
A. 可燃性粉尘
B. 导电性粉尘
C. 可燃性飞絮
D. 爆炸性粉尘环境
【单选题】
___0190.根据《爆炸危险环境电力装置设计规范》（GB 50058—2014），（ ）是指在大气条件下，气体、蒸气、粉尘、薄雾、纤维或飞絮的形式与空气形成的混合物引燃后，能够保持燃烧自行传播的环境。
A. 可燃性粉尘
B. 爆炸性环境
C. 可燃性飞絮
D. 爆炸性粉尘环境
【单选题】
___0191.《爆炸危险环境电力装置设计规范》（GB 50058—2014）规定，在正常运行时，预计可能周期性或偶尔释放的释放源是（ ）。
A. 零级释放源
B. 连续级释放源
C. 一级释放源
D. 二级释放源
【单选题】
___0192.《爆炸危险环境电力装置设计规范》（GB 50058—2014）规定，贮有可燃液体的容器上的排水口处，在正常运行中，当水排掉时，该处可能会向空间释放可燃物质可划为（ ）。
A. 连续级释放源
B. 二级释放源
C. 一级释放源
D. 零级释放源
推荐试题
【单选题】
Which log file would assist in identifying an issue that occurred during the database export phase of a vCenter Server upgrade process?___
A. vcdb_import.out
B. export.json
C. export-upgrade-runner.log
D. vcdb_export.out
【单选题】
Bidirectional CHAP is support by which storage initiator?___
A. software FCoE HBA
B. Fibre Channel HBA
C. independent hardware iSCSI HBA
D. dependent hardware iSCSI HBA
【单选题】
What is a pool of raw storage capacity that a storage system can provide to Virtual Volumes?___
A. protocol endpoint
B. storage container
C. storage provider
D. datastore
【单选题】
vSphere 6.5 DRS is now Network-Aware. Based on network utilization, when will DRS balance VMs?___
A. DRS will balance VMs when a network resource pool is configured for VMs.
B. DRS will balance VMs when Network I/O Control is enabled.
C. DRS will place VMs on initial boot for hosts that have network utilization lower that the threshold.
D. DRS will vMotion VMs when network utilization is higher than the threshold on a particular host.
【单选题】
A scripted upgrade of ESXi fails due to an incorrect parameter in the upgrade script. What file must the administrator modify to correct the problem?___
A. vmreconfig.pl
B. hostinfo.pl
C. ks.cfg
D. boot.cfg
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machine VM2. If a user is a member of group A and B, what action can the user perform?___
A. Suspend VM2.
B. Power off VM1.
C. Power on and power off VM1.
D. Power on and power off VM2.
【单选题】
The networking team has requested to have a dedicated network for iSCSI traffic. This task has been assigned to the vSphere Administrator. What is the VMware-recommended way to accomplish this?___
A. Configure Static Routes on each ESXi Server.
B. Configure the right subnet.
C. Create a custom IP Stack.
D. Define a dedicated gateway for the iSCSI vmkernel.
【单选题】
To prevent possible failures or issues during a vSphere upgrade, which component should be upgraded first?___
A. ESXi Hosts
B. virtual machines
C. datastores
D. vCenter Server
【单选题】
What is the command for updating an ESXi host?___
A. esxcli software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
B. esxupdate software update –d”/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
C. esxcli software update –d “/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
D. esxupdate software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
【单选题】
A vSphere Administrator would like to identify which physical NUMA node their virtual machine is currently residing on. What esxtop metric would provide this information?___
A. GST_ND[x]
B. OVD_ND[x]
C. NRMEM
D. NHN
【单选题】
How can a vSphere administrator ensure that two virtual machines never run on the same datastore in a datastore cluster, while permitting the VMs to be load-balanced?___
A. Use an Intra-VM Anti-Affinity Rule.
B. Configure a storage DRS VM override.
C. Disable storage
D. RS for the VMs.
【单选题】
What is the VMware-recommended way to move a physical adapter out of Network I/O Control’s scope?___
A. Set the teaming policy to “Route Based on Physical NIC Load.”
B. Add the vmnic to the Net.NetNiocAllowOverCommit parameter in Advanced System Settings.
C. Add the vmnic to the Net.IOControlPnicOptOut parameter in Advanced System Settings.
D. Move the vmnic to a different vmUplink port on the Distributed Switch.
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machines, defined on the VM folder and its children. If a user is a member of Groups A and B, what will be the user’s effective permission on VM1 and VM2?___
A. Power on
B. Power off.
C. Power on and Power off.
D. Reset.
【单选题】
Group 1 is granted console interaction on a VM folder. User 1 is granted no console interaction on the same VM folder. What will be the outcome if User 1 tries to access the console of a virtual machine?___
A. User 1 will not be able to access the virtual machines in the VM folder.
B. User 1 will not have access to the virtual machine console.
C. User 1 will have access to the virtual machine console.
D. User 1 will have console access only via the vSphere Web Client.
【单选题】
Which statement is true regarding the use of VMFS3 datastores with vSphere 6.5?___
A. VMFS3 datastores can be used but not created.
B. VMFS3 datastores can be neither used nor created.
C. VMFS3 datastores will be present but unmounted.
D. VMFS3 datastores can be created and used.
【单选题】
In the Exhibit, each VM has a 1GHz non-expandable reservation. If all VMs are powered on in sequence, what would be the outcome?___
A. VM4 cannot be powered on.
B. VM5 cannot be powered on.
C. VM6 cannot be powered on.
D. VM3 cannot be powered on.
【单选题】
vSphere 6.5 introduced MAClearning capabilities for VMware’s virtual switches. What three benefits will it provide? (Choose three.)___
A. Reduced memory consumption.
B. Reduced consumption of extra CPU cycles.
C. Increased network throughput.
D. Prevent packet flooding inside the vSwitch.
【单选题】
What is the default pathing policy for most active-active arrays?___
A. Fixed
B. Most Recently Used
C. Dynamic
D. isk Morroring
【单选题】
Which command will show the iSCSI sessions on a ESXi 6.5 host?___
A. esxcli storage iscsi session get
B. esxcli iscsi session get
C. esxcli storage iscsi session
D. esxcli iscsi session list
【单选题】
Which of the following is not a parameter for traffic filtering or marking?___
A. virtual port ID
B. Protocol
C. Traffic Direction
D. DSCP value
E. Traffic redirection
【单选题】
A vSphere administrator wants to enable a virtual machine with Secure Boot, but in VM setting, Secure Boot option was not found under Boot Options. What could be the cause?___
A. The virtual hardware is not compatible.
B. The virtual machine has missing drivers.
C. The virtual machine OS does not support secure boot.
D. VMware Tools is not upgraded.
【单选题】
A virtual machine is connected on a distributed port group where the average bandwidth configured in the traffic shaping policy is 100 Mbps. The VM network adapter is configured with a reservation of 200 Mbps. What is the VM’s effective bandwidth?___
A. 200 Mbps
B. 100 Mbps
C. 150 Mbps
D. 400 Mbps
【多选题】
What are two reasons why a datastore in a Storage DRS cluster cannot enter maintenance mode?(Choose two.)___
A. Storage latency is too high to allow Storage DRS initiate Storage vMotion.
B. Storage DRS is configured for a VMFS3 datastore.
C. Storage
D. RS is disabled on the virtual disk.
【多选题】
What two methods are used to configure VMware vSphere Storage I/O Control shares and limits? (Choose two.)___
A. Assign shares and limits to VM virtual disks.
B. Assign shares and limits to datastores.
C. Assign shares and limits to Storage (DRS) clusters.
D. Assign shares and limits using VM storage policies.
【多选题】
ESXi 6.5 introduces VMFS6, which supports both 512e and 512n devices. What three configurations are supported when using these devices? (Choose three.) ___
A. Hosts with both 512e and 512n devices.
B. Storage vMotion between both 512e and 512n devices.
C. Datastore Extents spanned between both 512e and 512n devices.
D. Storage DRS clusters containing only both 512e and 512n devices.
【多选题】
A vSphere Administrator observes that the Primary VM configured with Fault Tolerance is executing slowly. After further investigation, it is determined that the Secondary VM is on an overcommitted ESXi host. What two methods will correct the problem? (Choose two.)___
A. Use Storage vMotion to migrate the Secondary VM to another datastore.
B. Use vMotion to migrate the Secondary VM to a different ESXi host.
C. Configure a CPU limit on the Primary VM which will also apply to the Secondary VM.
D. Turn off and turn on FT in order to recreate the Secondary VM on a different datastore.
【多选题】
Which two features require the use of Host Profiles? (Choose two.)___
A. Host Customizations
B. shared storage
C. Auto
D. eploy
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
Which two statements correctly describe VM-Host affinity rules? (Choose two.) ___
A. When there is more than one VM-Host affinity rule in a vSphere DRS cluster, the rules are applied equally.
B. After creating a VM-Host affinity rule, its ability to function in relation to other rules is predetermined.
C. When there is more than one VM-Host affinity rule in a vSphere
D. RS cluster, the rules will be ranked.
【多选题】
An administrator wants to enable proactive HA by moving virtual machines automatically if a hardware alert is triggered. What are the three required settings? (Choose three.)___
A. Set vSphere DRS Automation to Partially Automated.
B. Turn on Proactive HA.
C. Set the Proactive HA Automation Level to Manual.
D. Set the Proactive HA Automation Level to Automated.
E. Turn on vSphere HA and vSphere DRS.
【多选题】
If vCenter Server 5.5 installation has one or more services deployed remotely, which three services are relocated to vCenter Server 6.5 on upgrade? (Choose three.)___
A. vCenter Inventory Services
B. vSphere Authentication Proxy
C. vSphere Web Client
D. vSphere
E. SXi Dump Collector
【多选题】
What two debugging levels can a virtual machine be configured to? (Choose two.)___
A. Verbose
B. Debugging
C. Statistics
D. Trivia
【多选题】
What are three benefits of using a few large-capacity LUNs instead of many small-capacity LUNs? (Choose three.) ___
A. Better performance because there is less contention for a single volume.
B. More flexibility for resizing virtual disks.
C. Less wasted storage space.
D. More flexibility to create virtual machines without adding new LUNs.
E. Fewer VMFS datastores to manage.
【多选题】
Which two configurable options are available in Boot Options for a virtual machine? (Choose two.)___
A. Tools Upgrades
B. Encryption
C. Firmware
D. Force BIOS setup
【多选题】
Which three VMware-recommended best practices should an administrator follow before upgrading to vSphere 6.5? (Choose three.)___
A. Disconnect ESXi host from vCenter.
B. VMware Tools are installed in the virtual machine.
C. Ensure that the system hardware complies with ESXi requirements.
D. Back up the host.
E. Check the interoperability of any other software integrated with vSphere.
【多选题】
What are two requirements to enable EVC in vSphere DRS cluster? (Choose two.)___
A. CPUs must be from the same vendor.
B. EVC must use the lowest possible baseline supported by the hardware.
C. CPUs must be in the same family and of the same speed.
D. No VMs may be running in the cluster.
【多选题】
What three conditions could result in VMware Flash Read Cache being unable to claim a disk? (Choose three.)___
A. The disk is not listed in the VMware hardware compatibility guide.
B. The disk is not detected as an SSD.
C. The disk is not detected as local.
D. The disk is in use by VMFs.
【多选题】
Boot from SAN is supported on which three storage technologies? (Choose three.)___
A. VMware vSAN
B. FCoE
C. NFS 4.1
D. iSCSI
E. FC
【多选题】
Which two components are part of storage I/O multipathing on ESXi? (Choose two.)___
A. SATP
B. VASA
C. PSP
D. VAAI
